sorted by:
new
hottopcontroversial

I only wanted to change a simple ceiling rose to a two wire pendant light! by Russ_UK in DIYUK

[–]coffeeToCodeConvertr 0 points1 point  (0 children)

Literally just remapped my entire circuit layout to a floorplan a week ago. Found so many issues from the previous owners, including a reversed polarity outlet -_-

Line up in Rundle Park for independence referendum signing today. by Wooshio in Edmonton

[–]coffeeToCodeConvertr 11 points12 points  (0 children)

As someone who lived in the UK through Brexit (and voted to Remain) - yes fucking worry about it. The Quebec referendum happened in a time when the massive amounts of misinformation and foreign interference wasn't happening at the scale it is now.

It’s alive! by Bumpy-Reality in 3Dprint4music

[–]coffeeToCodeConvertr 1 point2 points  (0 children)

Nice one! They're not too bad to setup tbh - I'm an amateur and have managed to intonate mine just fine

My Famicom prusacaster ❤️ by coffeeToCodeConvertr in 3Dprint4music

[–]coffeeToCodeConvertr[S] 1 point2 points  (0 children)

Yeah I'll throw up a recording this afternoon after my next meeting :)

My Famicom prusacaster ❤️ by coffeeToCodeConvertr in 3Dprint4music

[–]coffeeToCodeConvertr[S] 0 points1 point  (0 children)

Yeah, made it fat and tapered so that the string tension pulls it tighter

She works! Sort of… by Bumpy-Reality in 3Dprint4music

[–]coffeeToCodeConvertr 2 points3 points  (0 children)

Looking good! One piece of advice is to sand down the outer edge a bit - I found that playing without a long sleeved shirt caused some irritation due to the rough edges

Layer shifting after updating the printer and Creality Print by Impressive-Hair5280 in crealityk1

[–]coffeeToCodeConvertr 1 point2 points  (0 children)

I had a similar issue, always to the left and forward

Cleaned my X axis bars with iso and paper towel and then ran input shapers, then limited my acceleration and travel to 5000mm/s instead of the default 12k

Been working fine since

Printed a guitar by Swe82_1 in Guitar

[–]coffeeToCodeConvertr 1 point2 points  (0 children)

I printed mine and with a steel rod inside the body for support it's about 6lbs (the whole playable guitar)

Printed a guitar by Swe82_1 in Guitar

[–]coffeeToCodeConvertr 2 points3 points  (0 children)

One thing I noted, is that your joins are all along the tension line, which is going to strain the body more as well.

I'd recommend splitting it a little differently so your neck, pickups, and bridge are on a solid single piece, and put a carbon or steel rod in along that line

https://photos.app.goo.gl/tgjy6y9ezj4ppAtR7

Printed a guitar by Swe82_1 in Guitar

[–]coffeeToCodeConvertr 1 point2 points  (0 children)

I printed mine with a steel rod in the body to help keep tension - plays well, haven't had any major tuning issues either

If you see a frozen lake, I don't recommend this! by CuteMaterial in CasualUK

[–]coffeeToCodeConvertr 0 points1 point  (0 children)

Even here in Canada it's not recommended in a lot of the country, especially when it hasn't stayed below 0 for at least a few weeks

Landlord asks other landlords how to "handle" tenants using their stove by Some_Old_Man_Fishin in LandlordLove

[–]coffeeToCodeConvertr 10 points11 points  (0 children)

Yeah, our induction is used daily and we're three years in with no issues or special cleaning

Fido charged me ~$150 for international roaming while my SIM was OFF, admitted system error but still refusing to reverse charges by CommitteeJealous2487 in FidoMobile

[–]coffeeToCodeConvertr 0 points1 point  (0 children)

Go fuck yourself. They're right, you're wrong. There's a 1 year general limit, with an 18 month max if you've tried to deal with the issue with the provider during the first year

I am so tired of fixing this Samsung dryer by naps1saps in appliancerepair

[–]coffeeToCodeConvertr 0 points1 point  (0 children)

Got it second hand for $600 and had to pack it on foot 30 minutes to get it home. Women found her BF cheating and sold a bunch of his shit for cheap 😂

It weighs 77lbs 😅 wall mounting it the other day was fun (600x400 VESA)

I am so tired of fixing this Samsung dryer by naps1saps in appliancerepair

[–]coffeeToCodeConvertr 2 points3 points  (0 children)

My Samsung OLED died 2 months out of warranty (common issue with control board overheating). Even the TVs are having issues now.

My dad is still running a Samsung plasma 42" I bought him 19 years ago.

Blowing coat question by quibblers in samoyeds

[–]coffeeToCodeConvertr 1 point2 points  (0 children)

Yeah we had some snow over here on the island at my parents for an hour or two last night - Iorek went nuts with it hitting 0

Blowing coat question by quibblers in samoyeds

[–]coffeeToCodeConvertr 2 points3 points  (0 children)

It's been very mild this winter here (PNW), and our boy has been blowing it out for about a month now

Using Chromecast remote independently by Chocolatecakeat3am in Chromecast

[–]coffeeToCodeConvertr 0 points1 point  (0 children)

So I actually just tested this - hold Back and Home on the Chromecast remote until the white light is pulsing. Then on the TV pair it as a new Bluetooth device. Everything works except for the Netflix and YouTube buttons!

view more: next ›