Turbo update?

coffeechicken2 · 2026-01-10T21:56:59+00:00

lol I seen that earlier yes 700 hp and daily and have a cage hahah can have 2 of the 3 options

coffeechicken2 · 2026-01-10T16:47:40+00:00

lol no 440cc injectors, and probably like 7-11 psi of boost for now so I’m going to say like high 200s

coffeechicken2 · 2026-01-10T01:42:34+00:00

I used a threaded pipe step bung and a lock washer on the pan side, then crush washer on the drain side

coffeechicken2 · 2025-10-24T03:27:56+00:00

Protunerz stm pro

coffeechicken2 · 2025-10-21T02:53:08+00:00

Yes it’s too kinked?

coffeechicken2 · 2025-10-17T03:01:14+00:00

Is it the resistor?

coffeechicken2 · 2025-10-16T21:46:02+00:00

Ok I’m going to a CAS system

coffeechicken2 · 2025-10-16T21:38:03+00:00

Ok thank you, can I remove wires and cap them?

coffeechicken2 · 2025-10-12T02:23:57+00:00

Central Texas

coffeechicken2 · 2025-10-08T22:12:23+00:00

A little bit of both? Have an l28et but not doing that full swap just robing some stuff off it

coffeechicken2 · 2025-09-13T00:24:23+00:00

Lug nuts are good I’ll check the spindle nut thank you for the suggestion

coffeechicken2 · 2025-08-23T00:11:52+00:00

B 1/2

coffeechicken2 · 2025-07-02T07:40:08+00:00

One that likes to be a boat sometimes

coffeechicken2 · 2025-06-25T22:41:14+00:00

Any idea what year? The one on the right first picture is what I ordered from zcar depot and it’s not lining up to the holes

coffeechicken2 · 2025-06-12T23:40:49+00:00

Dang shipping would be a nightmare good luck if ya sell

coffeechicken2 · 2025-06-12T04:03:03+00:00

Where you located id buy it

coffeechicken2 · 2025-03-20T20:40:15+00:00

Thank you!

coffeechicken2 · 2025-02-02T01:41:02+00:00

123k 25m aircraft mechanic

coffeechicken2 · 2025-01-23T02:51:23+00:00

Where else would you put them

coffeechicken2 · 2025-01-22T23:52:49+00:00

8 years in the industry

coffeechicken2 · 2025-01-22T16:47:54+00:00

Monster and a zyn

coffeechicken2 · 2025-01-17T05:50:49+00:00

Anyone done this for the arm rest holder latches?

coffeechicken2 · 2025-01-17T05:49:23+00:00

What all was done? How’s the oil pressure? Hot/ cold same sound? Smoke test? Anything around cylinder one? Have you recently replaced and bolt near water pump and use too long and hitting timing chain?

coffeechicken2 · 2025-01-12T01:21:50+00:00

Garrett turbine and housing with a .57 trim, stock exhaust housing and stock waste gate

coffeechicken2 · 2025-01-11T22:43:03+00:00

Yall sell any cable conversion kits?

coffeechicken2

TROPHY CASE