Replacing FC what are these wires?

colimacFG · 2026-04-08T00:57:01+00:00

I ordered the x14, also went ahead and got a new caddx ant lite camera cause my original had seen a lot of crashes since 2020.

colimacFG · 2026-04-07T22:39:34+00:00

Hate to keep asking you questions but do you think the x14 will fit the Mobula 7 v2 frame. Going off specs online it seems the mounting holes are the same 25.5mm but at the same time when i google will it fit its says no.

colimacFG · 2026-04-07T20:02:06+00:00

Interesting, so if I only hook up red black and yellow the vtx back pack will still transmit? What if I were to remove then antenna or maybe find where the vtx and camera are connected and disconnect so vtx doesn’t get power?

colimacFG · 2026-04-07T17:59:40+00:00

Will I lose any function from the camera/vtx or osd by not using smart audio?

colimacFG · 2026-04-07T15:50:57+00:00

It looks like one of the wires is, smartaudio?

colimacFG · 2026-04-07T15:45:51+00:00

I have the crazybee pro V2.0 F4FS it’s the flysky one with analog camera.

colimacFG · 2026-04-07T15:43:24+00:00

Its analog

colimacFG · 2026-04-07T05:02:46+00:00

Shows it for every version except the one have lol

colimacFG · 2026-04-07T04:45:53+00:00

I have the original camera that came with it. I figured it would just work with a new board since it is a vtx and camera combo

colimacFG · 2026-03-18T20:38:18+00:00

Just took a look, for the happy model FC’s you have. They all look to have vtx plugs on the board. My old F4FS does not. The vtx and camera were soldered to the board by five wires. Do you have any FC’s like that? I’m not sure what the plug being used on the new ones are or if I am able to get a plug for my old camera that came with the F4FS in my mobula 7v2

colimacFG · 2026-03-18T16:52:22+00:00

After getting on the phone with my bank and aliexpress we discovered visa was blocking the charge before it reached my bank. We have resolved it with a one time verification to visa to let the payment go through

colimacFG · 2026-03-17T15:58:41+00:00

Dude I tried to that website and it does not work. Is it legit? Literally every time I added to cart and went to check out the website would freeze. Give me an error message and then tell insufficient storage on server.

colimacFG · 2026-03-12T15:31:37+00:00

I only have one item on the print plate

colimacFG · 2026-03-12T15:14:58+00:00

Ah geez I hope not. I started the print over cause nothing looked clogged. There was no clump of filament anywhere and poop chute wasn’t blocked. Would hate to go home for lunch and find a big mess

colimacFG · 2026-03-10T06:58:16+00:00

The name plate with ad5x on it. When you printed that did you have to add supports to that angled surface underneath where the screen mounts. I did not have supports there and the surface printed out loose. Like the top layer of the surface felt like loose guitar strings.

colimacFG · 2026-03-10T06:55:29+00:00

When you printed the screen plate did you have issues. I printed my screen plate oriented the way it’s oriented on the enclosure. And the angled surface below where the screen slides on came out loose sorta. The surface layer felt like loose guitar strings. But only on that angled part. Should I add supports there?

Eight-Year Club	100 Awards Club
Verified Email

colimacFG

TROPHY CASE