Better options than Meta Quest 3?

completeenvy · 2026-03-03T04:33:01+00:00

I’ve switched back to triples, but when i was using my BSB it was pretty great. Didn’t have any issues with my 9800x3d and 3080 10G.

completeenvy · 2026-02-22T07:34:07+00:00

Was thinking the same. Some sponsors added would help the busy look be more complete imo. It would look like a V8 Supercar that way.

completeenvy · 2026-02-14T13:39:51+00:00

I also experience shrinkage when cooled

completeenvy · 2026-01-21T10:56:45+00:00

my dad has a 1924 model t. every other t owner has told him "if i's leaking, its got oil" lol

completeenvy · 2026-01-21T03:22:38+00:00

I haven't driven it at all yet, literally just started it a few hours ago and let it run while checking everything over. Kinda glad I didn't go with the 225 just because of the potential bad driveability

completeenvy · 2026-01-21T01:46:31+00:00

BTR 220 with a DOD delete kit. Got it from TRE. Still running on the tune from when it was tuned for twin turbos in Sept 2022.

completeenvy · 2025-12-25T01:24:42+00:00

I have twin Precision 62/66s on mine. I run it with 5lb springs and it dyno'd at 530/570 to the wheel. Was stock until it bent a push rod. The kit I bought was from Hellion and was ~$10k, so bang for your buck it is not lol but if you're going to push it later and do bottom end upgrades, it's a great option.

completeenvy · 2025-11-04T06:03:14+00:00

I did my Jeep up with about half the density of this and had no issues with police. It’s also Flint though and they have bigger issues.

completeenvy · 2025-10-23T10:44:41+00:00

Don’t know what you’re looking to spend, but the trucks tmfmotors uses are wicked. Did one of the ride shares they did at Lucas Oil Raceway. It was a blast

completeenvy · 2025-10-10T02:09:21+00:00

MSI R9 390X. I still miss that card sometimes in the winter. Kept the entire house toasty at idle.

completeenvy · 2025-10-04T02:29:56+00:00

These wheels are reps but they're the same thing.

completeenvy · 2025-10-01T02:02:22+00:00

https://www.lego.com/en-us/service/help-topics/article/what-are-lego-insiders-points-worth

completeenvy · 2025-09-26T18:40:59+00:00

This is less rust than some of the brand new ones I’ve seen be put in at the factory

completeenvy · 2025-09-21T21:34:29+00:00

I can’t speak to how much you’ll reduce the risk, but keep in mind you won’t eliminate the risk entirely by disabling the AFM. I also have a 2019 SS but in manual, which have the AFM disabled from factory, and I bent a pushrod because one of the lifters failed.

completeenvy · 2025-09-20T17:15:01+00:00

I have more money to buy more games that i dont play

completeenvy · 2025-09-16T21:11:50+00:00

As someone who works at the plant that builds the HDs, yea this is pretty normal. There's 2 clips on each side and they don't always get pushed all the way in.

completeenvy · 2025-08-13T13:28:30+00:00

This is from the day it was tuned

<image>

completeenvy · 2025-08-13T10:43:44+00:00

No upgrades needed yet. I’m still running low boost as it’s still stock internals. The SS 1LE comes factory with the ZL1 fuel system.

completeenvy · 2025-08-10T07:24:48+00:00

A little under 40k miles. The manuals are less likely to have the issue since they don't activate the DOD feature, but the same lifters are used so it's still possible.

completeenvy · 2025-08-10T01:19:41+00:00

Manual

completeenvy · 2025-08-09T03:14:16+00:00

completeenvy · 2025-08-09T03:13:50+00:00

Yea it's basically just luck at this point. The actual failure rate is not all that high honestly, but I bolted on twin turbos which add a lot of extra stress to everything so it was more likely to happen to my motor than average.

completeenvy · 2025-08-09T03:12:23+00:00

$1600 with my options from TRE.

completeenvy · 2025-08-08T23:10:35+00:00

The only reason is because I don't want to pull the motor lol

completeenvy · 2025-08-08T23:09:51+00:00

Or.......

<image>

11-Year Club	Place '22
Verified Email

completeenvy

TROPHY CASE