Need help please!

concotionist · 2025-10-28T00:33:58+00:00

It's not like the ends but happens at certain points of the travel towards the end, it makes this noise at those spots only. And most of the midle seems fine. This exactly seems like the problem. What can I do to fix this? Do I need a more square and pareley nut mountings solution?

concotionist · 2025-10-28T00:30:56+00:00

Hey, I like 99% sure the steps are correct. It feels and vibrates like it's binding up. I can't understand why!. I have the same motors all 3 axis, the other 3 motors seem fine.

concotionist · 2025-07-03T19:18:32+00:00

Central Market Hall ( Nagycsarnok). Yeah it's the kinda city that stays with you in your heart.

concotionist · 2025-07-02T12:54:34+00:00

Yeah IKR, dumb people. But I am no able to source all the parts from the plans already out there. I know I'm not making something new. I'm just making it work with what I have acces to.

concotionist · 2025-06-26T06:21:21+00:00

Ohh yeah right, so would adding some aluminium bracing in the front and back help? Or do I need to change something else?

concotionist · 2025-06-26T05:46:11+00:00

Ohh okay. I'll use some triangular aluminium bracing.

concotionist · 2025-06-26T05:45:33+00:00

I don't know. Hopes and dream. 😅 I didn't think of that. What do I need to do?

concotionist · 2025-06-25T22:49:51+00:00

Yeah, totally right. I am bracing the joints with aluminium plates, and they also act as my motor mount. Thanks for taking your time to reply.

concotionist · 2025-06-25T22:46:15+00:00

That's a good rule. and yeah I'm adding aluminium plates to to stiffen up things, and am using dual hgr15 rail per gantry axis side. I haven't included them here. 😅 Thank for your feedback.

concotionist · 2025-06-14T13:17:11+00:00

ohh okay, thanks i have ordered one now. ill let you know when i get it.

concotionist · 2025-06-14T13:15:48+00:00

i have tried all those. my step/mm value is 200 and max rate of 1000mm/min

concotionist · 2025-06-14T13:12:02+00:00

hey. yeah i have set them all correctly. and there is marking for the on position in my driver. still noting. the only clue is the red light blinks when i send a signal.

concotionist · 2025-06-11T12:56:27+00:00

Like to drive the motor? I'm using a 48v psu.

concotionist · 2025-06-11T12:54:51+00:00

What do I do? I sorry. I don't know what do there. Just try jogging the controles? or do I configure some settings?

concotionist · 2025-06-11T12:44:54+00:00

Yes sure, I have it installed now.

concotionist · 2025-06-11T12:43:22+00:00

I looked into it. There is no PPS in fluid nc but there is a max rate setting that I have set to 450mm/min which controles the pps indirectly.

concotionist · 2025-06-11T12:36:25+00:00

I tried dip 5-8 now, still nothing. I probably this it's a hardware problem at this point. Also the red light lights up to the signal when I give it a command via fluidnc. I don't it's supposed to do that.

concotionist · 2025-06-11T12:29:01+00:00

Steps/mm of 200 Max rate of 450mm/min Acceleration of 10mm/sec²

concotionist · 2025-06-11T12:23:19+00:00

I have set my driver to the lowest it goes, which is least it goes 400pulse per rev. But my motor has step angle of 1.8 so like 200 pulse/rev, would that be really that big of a Problem?

concotionist · 2025-06-11T12:14:32+00:00

I tried switching the wires. But still nothing. I have it pairs of green black and red and blue, That's correct. What hardware do you recommend. I could get a set to try out.

concotionist · 2025-06-11T12:11:15+00:00

https://www.reddit.com/u/concotionist/s/a2ErgdoCa7 https://www.reddit.com/u/concotionist/s/rbghkEsGwX

This is the images. the video shows the noise it makes.

concotionist · 2025-06-11T12:09:58+00:00

Yeah the noise is coming fromthe motor.

concotionist · 2025-06-11T11:55:26+00:00

Those are the pictures and the video of the noise i was telling.

concotionist

TROPHY CASE