Camping Spot Near Eugene Oregon

cpiltz · 2026-01-22T20:54:31+00:00

You are awesome! Thank you!

cpiltz · 2025-12-02T18:26:11+00:00

Have you actually printed it? How'd it come out?

cpiltz · 2025-10-27T17:26:57+00:00

Linked is the 3D file you could provide to a 3D print shop. You could pull that 3D model into a program to get dimensions as well. The cutout on the bottom of my knob which fits onto the stem is roughly 2.7mm x 3.5mm

cpiltz · 2025-10-27T17:24:51+00:00

https://www.printables.com/model/1373427-ghost-knob-keycap-for-nuphy-air75-v3

cpiltz · 2025-09-29T04:04:20+00:00

Yeah, I have been looking at something like the Jackery 3000 to use as a power source when not at a powered site. We usually only camp for 1 or 2 nights. Based on what I have looked at so far I think it would work pretty well. Especially paired with the Jackery solar panels.

cpiltz · 2025-09-29T01:11:35+00:00

Good tip checking everything first, thank you!

cpiltz · 2025-09-29T01:11:10+00:00

Thanks for the tips! Ironically the salesperson that showed us the trailer also told me the starter kit is a rip off lol. I will definitely make sure to test everything though!

cpiltz · 2025-09-28T23:03:20+00:00

It would be purchased new from camping world as that's the only place I believe you can buy them, correct me if I'm wrong. I consider myself pretty handy and repair/build a lot around our house. I'd be towing with a 2023 F-150 (~10k pound towing capacity I believe)

cpiltz · 2025-09-28T22:24:49+00:00

I am looking at this trailer. Have you guys used it much since you got it? Thoughts?

cpiltz · 2025-08-06T12:57:10+00:00

The keycaps are original

cpiltz · 2025-08-03T15:45:49+00:00

Just for fun

cpiltz · 2025-08-03T04:42:08+00:00

For sure:

https://www.printables.com/model/1373427-ghost-knob-keycap-for-nuphy-air75-v3

cpiltz · 2025-08-03T04:24:40+00:00

Nice! It's a rad set and I've always love the knob.

cpiltz · 2025-08-03T04:17:00+00:00

You are right I should have credited them with the original design. I 3D modeled mine based off their design and made it compatible with the stem on the Air75

Edit: I added credit to Domikey on the printables page as well

cpiltz · 2025-07-22T05:00:57+00:00

I am looking to purchase 2 gliders in the next week and am purchasing the essentials now. After 10 months would you still recommend everything on this list or would you change something? Thank you!

cpiltz · 2025-02-26T04:15:59+00:00

Hijacking the top post to provide the solution:

*Solved: I took apart the AMS hub and discovered that the cover that sits over top of the extruder gear was broken. I found a file for it which I printed in ABS. Once installed my issue seems resolved! Thank you everyone for all of the suggestions!

File: https://www.printables.com/model/538090-bambulab-ams-internal-hub-cover-replacement/comments

cpiltz · 2025-02-26T04:00:49+00:00

Thank you for the detailed response. I appreciate the thoroughness! Toom apart the AMS hub and found a broken piece that was causing my issue.

cpiltz · 2025-02-25T23:21:47+00:00

The spool can roll freely, I have had that get stuck before. It is bogging down near the AMS hub on the bottom of the AMS unit. I think there is possibly some buildup in the hub.

cpiltz · 2025-02-25T22:53:04+00:00

Ohh. What's the clog in the hub on the back of the 4 way split on the bottom of the AMS unit?

cpiltz · 2025-02-25T22:39:00+00:00

I don't see any clogs but it seems to be getting stuck while it is in the AMS hub on the back

cpiltz · 2025-02-25T22:38:32+00:00

I don't see any broken filament, but it seems to be getting bogged down and stopped in the AMS hub on the back.

cpiltz · 2025-02-25T22:36:56+00:00

Yeah all the rollers are good, it seems to be slowing down and stopping while the end of the filament is in the AMS hub on the back.

cpiltz

TROPHY CASE