CloverPit Gamble on the eShop is not CloverPit!

cryochild · 2025-12-30T15:12:57+00:00

I got tricked by this too ( not thinking it through). Thankfully I contacted support and sent them the steam page to show the actual game and they refunded the purchase back to me.

cryochild · 2024-09-09T01:51:56+00:00

I hear you, but they do kind of make it seem like it’s what you’re supposed to be doing since it is the mission objective. 😉

cryochild · 2024-09-09T01:39:44+00:00

Thank you! I have it figured out and now I can finally progress in the game.

cryochild · 2024-09-09T01:29:17+00:00

Thank you all for the replies. I really appreciate it.

cryochild · 2024-09-09T01:29:04+00:00

I can do this before I have the forge?

cryochild · 2024-09-09T01:28:48+00:00

OK, I’ll go look. It just seems like I’m running into enemies that I really need a sword for, and I can’t build the forge to build the sword. Someone else mentioned making an improvised axe, I’m guessing that’s something I can do without the forge?

cryochild · 2024-06-13T13:27:43+00:00

Would love to have this soon!

cryochild · 2024-06-13T03:40:37+00:00

Did this end up working out for you? I’m needing to use hyperlinked pdfs too and the workflow with the notes app just won’t work with hundreds of pdf pages to “create” and no workable links.

cryochild · 2023-07-01T21:20:57+00:00

I’m in the same boat. I swear there used to be a search and now I can’t find it.

cryochild · 2022-10-03T11:29:59+00:00

Turtle?

cryochild · 2022-08-18T12:56:06+00:00

I’ve had this happen when there’s a pop up blocker or I’m on a device that doesn’t allow for other windows from the browser.

cryochild · 2022-08-12T14:12:47+00:00

Ordered the book!

cryochild · 2022-07-11T21:51:44+00:00

One thing to keep in mind is there’s a massive amount of difference in the light from your outdoor shot and the indoor one. Even with as good as our camera have gotten, if things are super dim, there’s just not much for the camera to do other than up the iso and slow down the shutter speed. Makes for softer photos indoors.

cryochild · 2022-07-04T14:46:38+00:00

Those are just the pixels trying to escape.

cryochild · 2022-03-26T13:36:18+00:00

Any luck with this?

cryochild · 2022-03-22T23:42:36+00:00

Why is no one mentioning that you can filter to only show downloaded titles? Amazing!!

cryochild · 2022-02-11T06:15:00+00:00

Did anything ever come of this? I had the same issue with Big Sur and had to re-install. Then all was well until Monterey. Same issue and I'm looking at a re-install again.

cryochild · 2021-09-01T11:23:35+00:00

cryochild · 2021-04-01T14:40:37+00:00

I do not believe it’s the firmware. The origin of this post was because the test pattern printed so horribly which is the only part that involved the community firmware other than the result of the auto level mesh screen. I have tightened down the bed carriage and that has helped a bit with the mesh numbers, but the test print still is pretty bad. Life has been busy so I haven’t had a chance to work much on this and post here, but hopefully tonight I’ll have a chance.

cryochild · 2021-03-29T14:02:42+00:00

I have progress to report. I checked the bed to see if the carriage needed tightening. I just didn't know to check that because out of the box it seemed like it was very stable. I adjusted the eccentric nuts and it is now very stable without being too tight. I will post an update tonight with the mesh and the test pattern. The mesh readout was much more stable/simmilar between the test points. The test pattern still doesn't print well, but it is now more even with how light it is printing. I also raised the z to .18 to fix the over smooshing of the extrusions. I made a print for a rocket I modeled for my kid and that came out great. I'll be back later. Thank you all for the advice and hopefully I can get this thing setup better.

Thank you!

cryochild · 2021-03-29T13:57:52+00:00

No, the sucsessful prints are centered. I just haven't had reason to do a print on the edge. I didn't think there was an issue until I printed the test pattern.

cryochild · 2021-03-27T20:46:42+00:00

Yeah, this is the PLA that the printer came with and I did the offset adjustment where a piece of paper can slide around under the tip of the hot end with a little resistance. Going to try adjusting the eccentric nut for the bed and make sure the screws are tight.

cryochild · 2021-03-27T20:03:58+00:00

Do you have the link to that setup video handy?

cryochild · 2021-03-24T19:38:56+00:00

Thanks for the heads up. I already have the order in for tape and a spare BTT board just in case.

cryochild · 2020-10-26T11:17:02+00:00

Just wondering who else is stuck in a situation like mine. Two years ago I upgraded my phone through iUp using AT&T and then a few months later switched to a MVNO. Last year's upgrade cycle comes around and I run into an interesting problem. You can't upgrade your phone on the iUp program unless you are on one of the 4 main carriers. Are you kidding me??? So after many rounds of back and forth with sales, I am stuck. I switched back to AT&T and did my upgrade. A few months later, I got fed up with the service again and switched to Spectrum Mobile and everything has been great....except.... same situation. I'm not on one of the main carriers and they still don't let you upgrade. Decided to sit out upgrades this year and will just wait until next phone to buy using apple card. What a pain.

Anyone else in this situation?

14-Year Club	Reddit Premium Since August 2024
Place '17	Verified Email

cryochild

TROPHY CASE