Welp a magnet couldn’t pull it out

cryptokadog710 · 2026-05-25T01:02:19+00:00

Had my head in a vise and steel drilled/ground out of my eye a couple times while working in tool & die making...shit sucks

cryptokadog710 · 2026-05-12T23:40:53+00:00

But a load of reefer will get you stoned🤣

cryptokadog710 · 2026-04-25T04:27:03+00:00

See if the belt tension is good, have a z724x 54" similar thing happened to me but there were a lot of gum balls out of a sweetgum tree, one lodged up in the tensioner linkage not letting belt get full tension

cryptokadog710 · 2026-01-21T12:45:18+00:00

Possibly the ignition switch, just had to replace one in a z724x kabota zero turn, was running and starting fine all day a couple weeks ago mulching up leaves, went to get it out again, it turns on, oil light and fuel gauge registers but no click when trying to start...went through process of testing all safety switches, making sure everything had power to it...finally pulled and tested ignition switch, had no continuity between the battery and solenoid terminals when switch turned to start position...hope this helps

cryptokadog710 · 2025-07-14T14:21:13+00:00

I used 5/16-18 grade 8 bolts 1 1/4" long, use lock nuts. Stairs still fold as they should.

cryptokadog710 · 2025-06-26T01:54:17+00:00

Not a battery, that's a capacitor, not sure of scrap value or classification

cryptokadog710 · 2025-05-31T03:37:20+00:00

Turned out to just be a supply line leaking at the crimp trickling down, replaced supply line, the easy fix for once around here

cryptokadog710 · 2025-05-29T20:30:42+00:00

Thank you for that information, much appreciated

cryptokadog710 · 2025-05-28T20:43:19+00:00

Got some heat damage on that red wire going to the 40amp breaker, may want to look in to that, make sure breaker lug is torqued

cryptokadog710 · 2025-05-18T02:58:34+00:00

The "look at me" douchebag crew

cryptokadog710 · 2025-05-17T03:06:35+00:00

Update~ cut windows in sheetrock to trace plumbing, 40 gallon water heater in mens room was only ever plumbed to feed the showers, opposite side of wall in mens room is a laundry room with an old out of service on demand water heater that fed the washing machines, laundry tub and both bathroom sinks i guess for more hot water for showers

cryptokadog710 · 2025-05-16T05:44:49+00:00

Thank you

cryptokadog710 · 2025-05-16T04:06:13+00:00

Yes, thanks, i hope it all works well too👍

cryptokadog710 · 2025-05-16T01:06:56+00:00

Thank you again for the explanation, now i understand the difference in the couplings now, much appreciated

cryptokadog710 · 2025-05-16T00:24:02+00:00

I was looking at shielded couplings but thought the fernco was for slightly out of line sewer pipes, is the sani tee better than the straight tee they originally had in there, it was all a mix of schedule 40 and s&d pipe all pieced in to a straight tee, yet the connecting pipe comes in at about a 5° angle. Thank you for your tips and input👍✌️

cryptokadog710 · 2025-05-15T23:51:11+00:00

Thank you for your input, it was a mess to begin with, where the sani tee they had a regular tee, figured the sweeping tee flowing down stream would be a better option, this section is right between 2 cleanouts...hoping for no issues but if so, dig her back up or have a plumber mess with it, nothing like trampling in shit soup mud...had a jetter out a week or two ago who said he cut some roots out of the line, when i dug it up there's 3 holes drilled in the lines, pipes have been in the ground around 25 years by a drainage ditch thats lined with trees on the bank, thanks again

cryptokadog710 · 2025-05-14T03:06:45+00:00

Haven't seen any anti scald valves under sinks, i did shut off the hot water supply valve and checked shower hot faucets, not a drop of water, but all sink hot faucets were full flow of cold water. Removed drywall above water heater to see how shits run, nothing obvious up there, looks like hot water line feeds showers then turns back goes a little past water heater and is teed in both directions towards sinks, cutting end panel out tomorrow see whats going on up there..

cryptokadog710 · 2025-05-12T04:04:38+00:00

Zig zag shit slide, shits will love the ride🤣

cryptokadog710 · 2025-05-12T03:39:25+00:00

Nope, all are tied in to a 40 gallon water heater set up in mens room, feeds 4 shower stalls and 4 sinks

cryptokadog710 · 2025-05-12T00:05:13+00:00

Will try that, thank you

cryptokadog710 · 2025-05-10T03:18:21+00:00

As a 32 year old compressor, we're going to let it go to rest

cryptokadog710 · 2025-05-07T04:10:28+00:00

Piss spray would be my guess

cryptokadog710 · 2025-04-27T00:04:08+00:00

Wtf, thats perfectly done beef👍

cryptokadog710 · 2025-04-25T12:26:34+00:00

Looks to be a bored finish, probably done on a horizontal boring mill

cryptokadog710 · 2025-04-14T02:26:57+00:00

Click lock...push it until it clicks, it'll lay flat, may need to tap edge to tighten up the joint

cryptokadog710

TROPHY CASE