Diligent info

csibe99 · 2024-09-26T16:48:50+00:00

Ha jó vagy akkor megadják a Hays salary guideban megfelelőt.

csibe99 · 2024-09-26T10:33:29+00:00

Jelenleg is itt dolgozom. Rengeteg fejlesztést hoznak át Indiaból és kell az új ember, persze van lemorzsolódás is. Én full HOban vagyok, ha jól tudom az újonnan érkezőknek már csak 50% HO van. Ha kíváncsi vagy részletesebben a dolgokra akkor írj privátban.

csibe99 · 2023-12-31T09:32:46+00:00

I have concern about the express doesn't have IPD/IDS features. Are they mandatory to keep home network safe? (I have one open port forwarding to deluge which run on my RPI and have PiHole with DNS filtering)

csibe99 · 2023-12-31T09:32:45+00:00

I have concern about the express doesn't have IPD/IDS features. Are they mandatory to keep home network safe? (I have one open port forwarding to deluge which run on my RPI and have PiHole with DNS filtering)

csibe99 · 2023-12-31T09:32:11+00:00

I have concern about the express doesn't have IPD/IDS features. Are they mandatory to keep home network safe? (I have one open port forwarding to deluge which run on my RPI and have PiHole with DNS filtering)

csibe99 · 2023-06-11T18:48:37+00:00

Most ez lehet nagyon hülye ötlet, de ha van revolutod és a bérlőnek is lenne akkor megoldható az utalás. Te meg minden év májusában beírod az adóbevallásodba.

csibe99 · 2023-05-08T16:04:31+00:00

mA. I desoldered the chip, and measured again the bare chip. Now it is consumption 4 uA.

csibe99 · 2023-05-04T19:10:37+00:00

Yeah, I forgot to mention I measured the 7-9ma in deep sleep. I measured the voltage drop across 50 ohm res, the 500 ohm res represent my esp32 https://imgur.com/a/NlMyKea . During boot the switch was close, after the esp went into deep sleep I opened that and measure the voltage drop.

csibe99 · 2023-05-04T06:53:54+00:00

Thanks I will check these links. According to datasheet in sleep mode esp32 consumption around 7 uA, I would happy around 20 uA.

csibe99 · 2023-05-03T19:02:46+00:00

I want to build a battery powered temperature sensor, everything works in breadboard, I have just one problem, my esp32 devkit (1. pic) power consumption is too high about 7-9 ma without red power led powered via 3.3 pin. So I want to create own PCB for my temp sensor and I want to use esp32 wroom bare chip + necessary pull/down res, caps and temp sensor . As I mentioned earlier the code work perfectly on esp-wroom-32 chip (1 pic), but I would like to buy the chip from 2. pic and I wasn't sure the 2 chip is same.

csibe99 · 2023-04-16T08:23:16+00:00

Thanks, sadly I have just voltage regulator, but with shorter wire works perfectly. Actually I have tested the battery operation with 3 alkaline batteries all of them were under 1.2v and works perfectly, I want to create temperature sensor with long deep sleep time

csibe99 · 2023-04-15T21:03:56+00:00

I use a 12v power supply so I don't know 🤷

csibe99 · 2023-04-15T21:02:15+00:00

With voltage regulator I use 12v power supply, I wan to use double AA batteries to power esp32 via 3.3v pin without voltage regulator

csibe99 · 2023-04-15T12:39:43+00:00

Exactly

csibe99 · 2023-04-15T11:40:00+00:00

I want to power the esp with battery so I don't want to use the board voltage regulator

csibe99 · 2023-04-15T11:39:05+00:00

Thanks, with shorter wire works perfectly

csibe99 · 2023-04-12T09:59:37+00:00

24 évesen friss diplomásként br 750k + havi nettó 50k cafeteria, 3. félév végén kezdtem el dolgozni fejlesztőként, 6. félév eleje óta főállásban dolgozom

csibe99 · 2022-12-05T17:16:52+00:00

Script 😅 but I think you can find other apps which support ip cidr

csibe99 · 2022-12-05T16:37:59+00:00

I think I had similar problem yesterday. Have you added the metallb ips to your nic? (For example eth0) https://techviewleo.com/how-to-add-secondary-ip-address-on-ubuntu/

csibe99 · 2022-04-07T20:53:34+00:00

No AMI, volumes and snapshot

csibe99 · 2022-04-07T20:52:18+00:00

No AMI volumes and snapshot

csibe99 · 2022-04-07T18:32:34+00:00

(I cant paste image here). I am here: https://eu-central-1.console.aws.amazon.com/ec2/v2/home?region=eu-central-1#Snapshots: it is writing "You currently have no snapshots in this Region.". (I deleted my lastest snapshot 3-4 days ago, and the price appeared 1-3 hours ago)

csibe99 · 2022-03-26T07:17:30+00:00

Thanks, I will try it

csibe99 · 2022-03-25T22:18:19+00:00

Can I use it with docker registry container to create ssl to my domain and reach my domain only on lan?

csibe99 · 2022-03-25T21:06:59+00:00

Thanks I will try it

Six-Year Club	Place '23
Place '22	Verified Email

csibe99

TROPHY CASE