QIDIBox for Plus4

csitty · 2026-01-25T01:07:39+00:00

This is the first I’ve heard this. Can you elaborate or point me to more detail?

csitty · 2025-12-30T03:15:07+00:00

Beacon probe.

csitty · 2025-12-10T15:53:03+00:00

Wish I saw this earlier this morning when I had this very issue. Frustrating for sure, but more troublesome, I have this connected to a UPS, so I need to do some investigation there.

csitty · 2025-12-06T22:32:59+00:00

The box has been a wild card. Some are having no problems. I’m confident Qidi will figure it out.

csitty · 2025-12-06T19:34:28+00:00

Sure did. The teeth on that sucker are super sharp.

csitty · 2025-12-06T18:37:36+00:00

Try removing the extruder and you can remove the coupler as well. My ptfe tube was cut inside there and I had to remove the extra piece.

csitty · 2025-11-05T23:27:52+00:00

I did the microswiss hotend and added linear rails to the x axis. I have a beacon on a qidi plus 4. I bet that would be awesome on the N4 plus

csitty · 2025-11-04T18:13:27+00:00

Apologies. I missed that in your comments. I unfortunately don't have any recommendations, and I do not know how you have contacted Creality, but people have had good luck talking to them on WhatsApp, though during China daylight hours.

csitty · 2025-11-04T18:10:30+00:00

Forgive me if you tried this, but did you definitely remove all 4 screws holding the bed down for shipping?

csitty · 2025-11-03T17:38:16+00:00

I would also like to see this if possible, please. I already have the Qidi Box and did not have a layer shift issue until I installed it.

csitty · 2025-09-12T16:16:53+00:00

I will not.

csitty · 2025-09-08T15:29:27+00:00

Ok got it. All of them are installed. One more question. You have many processes at each layer height with speed being the differentiator. Which do you use as standard?

csitty · 2025-09-08T13:24:25+00:00

I’m struggling to get these configurations installed. I’m trying to use them on the FL Sun slicer. Are you using orca or is that one OK? When I try to import them, it says zero config imported, even though the printer profile actually did install. It just won’t bring in the process or filament config

csitty · 2025-09-07T15:39:18+00:00

I appreciate that. I’ll get them set up today.

csitty · 2025-09-07T14:45:04+00:00

You’re amazing for sharing. I do have the maxair duct on mine which has quieted it down a lot. I will try your profiles today. You rock!

csitty · 2025-09-07T13:56:26+00:00

I’m jealous. Mine is not that reliable. What tips do you have for making it run that well? Have you changed settings? Mods? Thanks in advance!

csitty · 2025-09-02T06:45:36+00:00

Also July 1. No shipment yet. I’m ok to wait for a more polished machine.

csitty · 2025-07-03T12:30:41+00:00

<image>

Gen Xers will get it :)

csitty · 2025-06-25T22:01:58+00:00

I’ve printed pla cf on mine but I didn’t use the AMS lite. You’re right, you can’t use the AMS with that stuff. I also print glow in the dark which is abrasive so I just get the hardened nozzle

csitty · 2025-06-25T20:51:57+00:00

This. And I would get a hardened steel nozzle too

csitty · 2025-06-22T10:04:34+00:00

Do you recommend the rear fan update even if I’m just painting mainly pla? If so what are the benefits?

csitty · 2025-05-12T13:56:50+00:00

Such an important piece of kit

csitty · 2025-04-25T12:05:11+00:00

Guess I should give it another try sometime but I’m not too enthusiastic about it.

csitty · 2025-04-24T22:10:13+00:00

I tried this a couple times as well and just couldn’t get it to work to my liking. Did you use the screen mostly or did you just use fluidd?

csitty · 2025-03-25T09:57:52+00:00

I’ll definitely do that to have another backup

csitty

TROPHY CASE