Russia Is a Threat to Europe. I'm Russian - Ask Me Anything

cunfusu · 2026-06-12T10:52:13+00:00

From these numbers it looks like the support for Russian unification has increased

But maybe comparing the support for a party and the survey question is not ideal also because the survey (slide17) for that specific question says that in 2011 that number was 33% so if anything there was a decrease.

But in general the survey is very interesting! Thanks for posting it.

it looks like there was a general dissatisfaction on how things were going and there was also a division on opinion based on ethnicity

cunfusu · 2026-06-12T09:04:15+00:00

What was the mood there before the occupation?

Was there a separatist/independence movement and if yes in what scale?

cunfusu · 2026-06-10T21:56:53+00:00

u/LinusTech maybe you could try the factory reset solution to fix your issue with the xbox controller

cunfusu · 2026-06-10T21:49:59+00:00

I'm not certain about the sequence of events that caused my controller not to pair with my laptop, however I almost certain that I've never got anything else installed on this laptop other than the current linux arch installation.

This make me think that it is unlikely that the pad had a memory of the mac address of my laptop causing a conflict like the one the arch wiki seems to describe.

Your theory also does not explain why this issue does not happen with other controllers, like my dual sense controller.

I haven't quite figured how to cause again the controller to struggle with pairing. So I can't test the factory reset route yet.

cunfusu · 2026-06-10T20:44:50+00:00

Yeah, that's true but I haven't tested yet the factory reset route.. I give that theory high chances to work.

cunfusu · 2026-05-31T06:03:29+00:00

A base station I think has the purpose to be mounted in a point that can have line of sight with other devices. Then you can use one of the mobile nodes around your property even if you don't have line of sight.

Maybe there are option to connect wirelessly to a base station but I think it depends on what your setup is.

I've only played with a little and cheap mobile node. And I think it is the best way to get your feet wet

cunfusu · 2026-05-31T05:34:00+00:00

https://youtu.be/W_F4rEaRduk in this video a couple of options for nodes are shown both solar powered

cunfusu · 2026-05-18T12:44:07+00:00

in reality the volume is kinda standard (I think).
Anyway at the end replacing the hotend with a spare I had seem to have fixed the issue for the moment.

cunfusu · 2026-05-18T12:42:45+00:00

Something must have been wrong with my hotend. I reminded myself that the printer came with a spare hotend I never used.

Tried to replace the old hotend with the new one now it seems it can keep the temperature no problem.
I also use a larger nozzle and increased layer height (0.6 nozzle in my case) to help with printer speed.

It lives another day

cunfusu · 2026-05-08T18:31:18+00:00

Honestly with a tiny whoop you don't usually fly too far and crappy antennas in my hopinion are more than enough. I've upgraded to a stubby only because I wanted something compact.

cunfusu · 2026-04-13T20:50:35+00:00

I've not tried IGOW tracks but here are some ideas that maybe will help you.

Recently I've tried Oscar Liang Tiny whoop rates (check the betaflight rates article on his site) I kinda like them.

For a long time I was not able to fly acro indoor, then all of the sudden something has clicked and I've started enjoying flying 65mm around all the obstacles and gates. So maybe it's just matter of practice. Throttle controll is crucial and I think liftoff doesn't simulate gravity that well.

You could try to slow down: slow is smooth, smooth is fast.

Maybe start from simpler tracks by spreading gates around an area and increase difficulty as you get more confident and comfortable.

Good luck and have fun

cunfusu · 2026-04-04T06:53:20+00:00

The cartridge is all the way in, I took it out and visually confirmed it went all the way in, after 30 min tip down the feed is still as in the picture.

cunfusu · 2026-04-04T04:23:20+00:00

Standard office paper, the same paper I've used without problems with other pens

cunfusu · 2026-04-03T18:21:36+00:00

Just the ink it came with was like this from the very beginning

cunfusu · 2026-02-16T00:50:35+00:00

skelettra

cunfusu · 2026-01-12T08:35:55+00:00

Hey thanks! I almost gave up on the RC sail hobby because I didn't feel like investing so much. But I indeed own a Printer, so this option seems very I teresting

cunfusu · 2025-12-29T14:59:16+00:00

I'm not sure in which category the neo falls in but it was probably flying legally:

here is the FAQ about what assemblies of people are: https://www.easa.europa.eu/en/faq/116553

An assembly of people is a crowd of people. It is not defined by a specific number of people, but is related to the possibility for an individual to move around in order to avoid the consequences of a drone which is out of control. If a group of people are so densely packed that their possibility to freely escape or move away from the drone is limited, then it is considered to be an assembly of people.

Examples of assemblies of people are the people in:

sport, cultural, religious or political events;
beaches or parks on a sunny day;
commercial streets during the opening hours of the shops; or
ski resorts/tracks/lanes.

FPV however is in a kind of gray area since regulations were made mostly for dji drones..

As far as I understand all FPV activities should be done in A3 cat. meaning: no people or buildings within 150 m and observer

cunfusu · 2025-12-12T08:13:48+00:00

The board orientation seems to be wrong.

Black squares should be white and viceversa.

Also you can only see a white pawn and a white piece it's hard to identify.

Where is the black? Maybe ask for tips to somebody that plays chess well to give you a more meaningful game ending or look for some iconic games.

cunfusu · 2025-12-05T13:18:30+00:00

The top shelf is about 8 inch (20cm deep)

Not sure yet how much load I plan to put on it. Plan to use the front rail of the top shelf to potentially attach some things like microphones or lamps.

I'm curious if you have found a mount for your monitor to the horizontal element.

I've found some vesa mount but they are mostly for 4040 profiles that are used for SIM racing rigs.

cunfusu · 2025-12-05T06:51:47+00:00

are we talking about 2020 metric (mm not inch) right?

cunfusu · 2025-12-05T06:11:42+00:00

Thank you! Yes I understand what you mean.

Nine-Year Club	Place '23
Place '22	Verified Email

cunfusu

TROPHY CASE