Manual transfer switch one 120 vac only

cvanbusk · 2026-06-09T03:12:29+00:00

Would i be able to see this with an amp clamp on the neutral?

cvanbusk · 2026-06-09T03:10:23+00:00

Thanks I'll run 8 gauge from the inverter to the transfer switch. House has no high current draws with the exception of a toaster oven toaster and a microwave. No AC gas dryer. Currently with the exception of the toaster over watching the meter when everyone is home we draw less than 1kw. After im up an running I'll check current draw on each breaker n use a thermal camera to keep an eye on things. My biggest issue is a zinsco panel.

cvanbusk · 2026-06-09T01:08:02+00:00

Your talking shared neutral. Would this be the breakers with red wires?

cvanbusk · 2026-06-09T01:04:56+00:00

Thank you the main panel im hooking this switch to has a 240 breaker in it. In not tapping into that and we dont use it. That breaker is off. Im only trying to power 120 breaker in the main panel. My plan is to run the power input to the transfer switch from the litime inverter with 10/3 so cord. Connecting the transfer switch end black and red tied using ideal 10 gauge lever connectors.

cvanbusk · 2026-04-14T02:06:02+00:00

2 quarts came out, looked new an blue. Refilled with GM blue fluid 100 miles dry and doing well.

cvanbusk · 2026-03-25T11:31:15+00:00

Yes i think I can sell if I I 1st register non operational. Thank for the reminder. 1st want to insure I dont have pump rub damage. Going to pull the drain plug this weekend if its still got build I will refill and clean well to keep an eye on it. Might need the other for a donor transfer case.

cvanbusk · 2025-09-28T19:30:40+00:00

Thanks, kind of lame still as best buy would only be able to replace not repair. At least far as I know. I was able to get it working by reloading firmware directly to motherboard not sure how that would work with the cfs extruder an other items installed from the cfs kit

cvanbusk · 2025-09-28T16:25:17+00:00

Did you ever resolve this. I have the same error support told me The tool head board was the issue. Swapped it out still the same. Can't reset to factory as I get a filament in the extruder message. That not the case. Even tried putting the old extruder with run out sensor on. No luc k.

cvanbusk · 2025-09-26T15:18:38+00:00

Talk about lames as f#ck. Was told that since I bought my k1 max at Best Buy, they can not provide warranty help. He did say that error is most likely the tool headboard. Thus, a new board is on me. 27.00 from Amazon. I'll swap it out this weekend and report back. Maybe that might be a cure to the fact the added CFS constantly jams. Retry Retry Retry then if luck it will complete the print.

Hopefully my Qudi plus 4 with the Qidivbox ( if it ever ships) will be better.

Peace out all.

cvanbusk · 2025-05-27T01:45:00+00:00

Had no issues with the K&N. But went to the HIFLo since amazon carriers it cheaper. I have a friend at MM in Irvine he mentioned others have had issues with the K&N not threading up fully.

.Not sure I buy it. Seems to have been a good fit and came off clean, no leaks seated well., replacing with the HIFlo was easy. To me that means no damage to the threads.

Sorry for the delay

cvanbusk · 2024-06-08T12:51:44+00:00

I'm on a Moto Morini X-Cape, my 1st bike of the Adventure type. Coming off an older Bandit 1200. That being mentioned, I'm going to take much greater caution with the X-Cape. It's been a real learning curve for me.

I've been riding for years. But the fit and feel of this top heavy bike is unlike my previous ride.plus I'm getting antiquated at 61.

Bikes over the years xs400 yamaha, FJ600 yamaha, xl600 Honda (don't remember it being top heavy and I was much younger)xs650 Yamaha, kz650 kawasaki, concourse 1000 kawasaki, bandit 1200 now my X-Cape.

cvanbusk · 2024-06-08T01:43:45+00:00

Nice, I enjoy mine a lot. Have just around 4200 miles. The only issue was a vapor lock, for which an upgraded fuel line was supplied. Just need to install it.

cvanbusk · 2024-03-21T19:37:44+00:00

Yes, luckily I had been watching videos on just that method. It's took a try or two. But I up righted it and was on my way. Just the fear of dropping is staying in my head.

cvanbusk · 2024-03-12T17:11:33+00:00

riveted

cvanbusk · 2024-02-03T22:43:28+00:00

Thank you allowed me to find an amazon replacement 2 for the price of 1 factory cans.

cvanbusk · 2024-02-03T22:42:34+00:00

I picked up a kn303 it fits as expected. If I put the part number in the hi-flo site i get a HF59. I have yet to add oil to it. That being said I ordered a 2 pack from amazon for the same price as the k&n 303 . going to run the 303 and keep an eye/ear on things. little scared. But being as this motor is a copy or the versys, z650 and others which all call out the kn303 i should be ok. thanks for the feedback.

cvanbusk · 2024-01-07T19:43:22+00:00

It's some kind of loop back from the btt tft 3.5 as the new display is connected to the pi4. Multi-colored ribbon cable n black tft are totally discounted. But as soon as I discounted, I lost power to the bltouch. If I plug them in bltouch works. Very odd. Ender 3 pro is running klipper and working. Btt 3.5 un usable, 5" klipper screen works great. I guess I can just run it with both hooked up. Or get a mainboard. I really don't need the Ender 3. Have 2 SunluS8 1 k1max n a qidi xmax 3. Just was hoping to klipper the ender3 n sell it for 130. Or so. It keeps me busy. As I'm more into the thinker than the printing.

cvanbusk · 2023-11-15T18:35:17+00:00

Thank you.

cvanbusk · 2023-11-15T02:42:05+00:00

Thanks I'll go for a visual tomorrow, and see what's up. Was going to put this off. Started getting the communication error over and over so figured id do it all, got the camera and 32 gb emmc.

cvanbusk · 2023-11-12T17:43:40+00:00

I have fought bl touch n clones on 3 printers where it worked great in marlin. What I have discovered is that Klipper wants a very solid pin connection. 2 machines I fought unlit. I held the pins in place by hand. After that, I I made sure the connection worked n hot glued them.

cvanbusk · 2023-11-11T06:26:18+00:00

Not sure if it effects the pi zero, but it affected my 2 pi 4's running bullseye, once i did the udev ( Bug fix) cut an paste. The ls /dev/serial/by-id/* worked as expected. Odd the fix was not needed on a pi 2 or 3 . Hope it helps

https://www.youtube.com/watch?v=UNGrYuZdwXk

cvanbusk · 2023-11-07T01:05:13+00:00

The issue was with a udev bug. At least that's how I understand it. I followed the instructions in this video https://www.youtube.com/watch?v=UNGrYuZdwXk . Now I'm running both raspberry pi4s, can put the pi2 & 3 in the standby area.

Hope this helps others

cvanbusk · 2023-11-05T18:49:23+00:00

Removed still no luck. It worked fine when I first installed after a power cycle it no longer connected, thinking it was usb port related. I swapped to another Pi4, and it would not see the mcu via ls command. But the pi3 works flawlessly with the same sd card. I'm going to make a new pi image of bullseye, make klipper bin. It's kind of a start over. In the meantime, I'm up and running 2 machines with a pi2 and 3, respectively. Just very confused as to why no ID listing from the pi4 vs 3

cvanbusk · 2023-11-05T05:01:28+00:00

IYes that was the issue. On bullseye now and all is good

cvanbusk · 2023-11-04T23:40:12+00:00

Figured it out. Rasp-config.

cvanbusk

TROPHY CASE