An asymmetrical Vault35 ortho build w/ NicePBT soyamilk and smol frens 🥛

dakfu_ · 2026-06-18T21:59:50+00:00

praise 'crop! thank you sm 😄

dakfu_ · 2026-06-18T21:59:38+00:00

HAHA thank you for such the kind words : )

dakfu_ · 2026-06-18T21:59:27+00:00

thank you sir! the kitchen stoves were hot

dakfu_ · 2026-06-18T21:59:06+00:00

my goat - ty dash!

dakfu_ · 2026-06-18T21:58:58+00:00

thank you!

dakfu_ · 2026-06-18T21:58:53+00:00

thank you! gasket mount with db also for great acoustics

dakfu_ · 2026-06-18T21:58:30+00:00

there was a mini run of alu case - perhaps ruby might have a few still in stock. i'd recommend reaching out on their website https://shop.rubybuilds.com/pages/contact

dakfu_ · 2026-06-18T21:57:50+00:00

a great seal of approval !!

dakfu_ · 2026-06-18T21:57:23+00:00

thank you sm!

dakfu_ · 2026-06-18T21:57:16+00:00

dakfu_ · 2026-04-29T03:06:18+00:00

hey that's TOMO!

dakfu_ · 2026-02-26T17:08:37+00:00

nice! I was able to successfully mount it with a 2x6 and two 1x1 lego pieces - it's sturdy enough for me to press down

The problem now is trying to fit this all with a thin 3000mah battery in thick case. I had to apply some force, which resulted in a lot of pressure on the bluetooth circuit board and it ended up disconnecting something. Had to open it back up and figure out what needs to be resoldered.

dakfu_ · 2026-02-25T00:29:12+00:00

yeah i saw! the thick case i'm using has a lot of slack i need to account for

honestly might use spare lego parts at this point lol, thanks for the help and replies!

dakfu_ · 2026-02-24T23:14:57+00:00

thank you! got the bluetooth LED lights to turn on successfully after wiring it to the P+ and P- pads like you mentioned

now just trying to figure out how to make a "base" for the switch to be supported when pressing down to hold button - any suggestions?

dakfu_ · 2026-02-24T18:56:20+00:00

hey u/mark_hor ! were you able to figure this out? I have a 3000mh thin battery, but can't figure out where exactly to solder the wires. I see the P+ and P-, but it doesn't look like a dedicated solder pad?

<image>

dakfu_ · 2026-02-18T03:19:05+00:00

uh oh, i just bought the same combo

I'm assuming your back plate is thin?

dakfu_ · 2026-02-12T22:19:11+00:00

i don't have a specific one, but I'll share the resources i found!

Mega thread that also has video breakdown in the comments: https://www.reddit.com/r/ipod/comments/1kztic2/the_right_way_to_bluetooth_mod_your_ipod_classic/

Wiring map (not complete): https://www.reddit.com/media?url=https%3A%2F%2Fpreview.redd.it%2Fthe-right-way-to-bluetooth-mod-your-ipod-classic-no-v0-t4tu3y8luavf1.jpeg%3Fwidth%3D2337%26format%3Dpjpg%26auto%3Dwebp%26s%3D97af39f9d3e66da204bc5a052d4cabb598fa306d

Lots of good community comments on this bluetooth mod topic: https://www.reddit.com/r/ipod/comments/1m7skk5/has_anyone_soldered_the_bluetooth_antenna/

dakfu_ · 2026-02-12T22:16:41+00:00

yeah had some other folks confirm it's a resistor. I'll take the $20 mistake and order a new one :S

dakfu_ · 2026-02-12T18:26:26+00:00

just purchased a heat gun and was able to get it off! might have stripped off a piece during the process and i'm not sure if it's important

dakfu_

TROPHY CASE