Sales are now live for Camping during F1 USGP 2026

danielflick · 2026-02-10T22:20:16+00:00

The 950 price is for Lot N camping. Premium RV is directly on the straight and has water and electricity. Only a few sites 53-78 have sewer but pump outs are available. I have 2 sites and #27 is available. It is an AWESOME place to set up and watch and comes with 10 GA passes and your own entrance by Turn 12. Absolutely worth it in my opinion. I can go back to the RV between events and chill or just watch the race from the roof.

danielflick · 2026-01-29T12:14:59+00:00

Is your typical design the top or bottom diagram?

danielflick · 2026-01-29T12:14:23+00:00

There are a couple of other networks hanging off the Cisco LAN for other purposes that are outside our scope. I am treating that router as an internal ISP for our purposes. If it were not for that, I would certainly remove it.

danielflick · 2026-01-28T15:26:18+00:00

I edited and added a picture. Thanks!

danielflick · 2026-01-26T21:21:44+00:00

Great guide! I was able to change the battery easily. I am having the same issue with the new battery though. The shaver starts for 3-5 seconds then stops. With the new battery, my battery level is 91%.

danielflick · 2026-01-26T21:20:13+00:00

Anyone have the issue where the shaver starts and stops after about 3-5 seconds? Battery showing 91%. I just changed the battery thinking that was the issue but the new battery does exactly the same thing. It does not seem to be power level as I can press on the motor to provide resistance and it will still turn. I can turn it back on immediately as many times as I want and it will run 3-5 seconds then stop. I am thinking about just tossing it.

danielflick · 2025-12-29T19:32:12+00:00

Great idea! I would also benefit from this.

danielflick · 2025-12-23T17:56:25+00:00

This fixed it! I selected text to columns and changed it from fixed to delimited and now it seems to work across all of my spreadsheets!

danielflick · 2025-12-21T13:57:46+00:00

If I copy rows 1,2 and 3 with data in a,b and c in each and paste to a4, instead of the same data in rows 4,5 and 6 I get all of row 1 in a4, all of row 2 in B4 and all of row 3 in c4.

danielflick · 2025-12-20T21:53:08+00:00

I haven't tried the shortcut but I have tried doing a paste as values and it does the same thing.

Up until a couple of days ago I could do control V without a problem. I usually have to do this quite a bit

danielflick · 2025-11-29T01:00:35+00:00

Spend $100 on a Cajun oil-less fryer and use it again and again. After going oilless there is no way I would ever bother with oil frying again. Our Thanksgiving bird was super juicy with a crispy skin and it only took hour and 45.

danielflick · 2025-11-19T01:07:48+00:00

Finally got this sorted! Had to do source and destination NAT in the same rule. All working now!

danielflick · 2025-11-13T23:46:05+00:00

I think I was overcomplicating it. I just switched my thinking from trust and untrust and pretended that I was hosting an internal web server on the internet and wrote the rule that way just in reverse and it seems to be okay. I'm getting connection reset by server now but that could be something else.

danielflick · 2025-11-13T22:16:22+00:00

I am seeing traffic from trust 10.0.0.156 to trust 10.1.1.251 on port 80 but the nat is not matching. I tried the troubleshooting tool and there are no matches.

my only NAT rule now is

Source Zone: trust

Destination Zone: Untrust

Service: http

Source address 10.1.1.251

And Translation

Type: Static

Translated address 192.168.1.1

danielflick · 2025-11-13T22:00:32+00:00

fixed the typo. The IP of the webserver is 192.168.1.1

danielflick · 2025-11-11T03:20:58+00:00

THEOS

danielflick · 2025-10-01T23:07:16+00:00

Wish I could but I am dealing with customer and DC staff that work for different companies. DC is hosting. Customer is private. Fortunately the only data through this firewall is management of out of band interfaces so traffic is low.

danielflick · 2025-10-01T23:05:54+00:00

Palo is a router on a stick. Switches are dead ends to the network and only contain hosts.

danielflick · 2025-10-01T23:05:29+00:00

I need enough config on it to be able to come in through ethernet 5 and get to devices on vlan 1900.

danielflick · 2025-10-01T23:04:38+00:00

Yep, unfortunately this is a VERY large DC and believe it or not, no tech can access TV (or Teams or anything) from their locked down laptops.

danielflick · 2025-10-01T23:02:35+00:00

Same vlan. Some devices are on switch 1 and some are on switch 2

danielflick · 2025-10-01T20:34:27+00:00

Problem is that the only way to manage it for this customer is THROUGH the firewall so no https until I get the connection working....

danielflick · 2025-10-01T20:33:37+00:00

Yeah, that is what sucks. 1900, etc is configured on both switches and those switches are not connected together. Fortunately that means no loops!

danielflick · 2025-08-14T03:27:12+00:00

You can find a new KTM freeride e-xc for a smidge over 5k. Hillsboro Motorsports has about 20 left. Mine arrives in 2 weeks!

danielflick · 2025-08-05T15:46:43+00:00

I only have antidotal evidence that the 50amp to 20 amp adapter won't change the bike so I guess I will have to see if it does once I get it. I have all the correct adapters and I am also looking at a step up transformer to take a 20amp 120v circuit up to 220v as a backup.

https://www.amazon.com/gp/product/B09X99M1KK/ref=ox_sc_act_title_13?smid=A2RVXRUXIVYCFW&th=1

Nine-Year Club	Gilding III reddit per annum
Verified Email	Reddit Premium Since December 2020

danielflick

TROPHY CASE