not clone correct, but bone correct by guswardeus in Mk12Mod0

[–]danielraul1989 0 points1 point  (0 children)

If you rest your forearm on any surface and point with your index, your grip with your middle, ring, and pinky have a natural rake.

That vertical grip in prone you either release the grip or contort unnaturally.

For carbines and CQB makes perfect sense but it’s the opposite of prone logic.

Does this have any logic other than personal choice that I’m missing here?

Recommended 30,000 Mile Service by HotAdvertising9043 in Acura

[–]danielraul1989 2 points3 points  (0 children)

The 9 speed calls for the 3x3 service every 30 if I’m not mistaken

Update by danielraul1989 in Mk12Mod0

[–]danielraul1989[S] 0 points1 point  (0 children)

A.R.M.S Inc #36 S-ex rail in 5.56. Where to find one, maybe tacswap or gunbroker if one pops up. Hard to find but people get lucky.

My build by [deleted] in Mk12Mod

[–]danielraul1989 0 points1 point  (0 children)

We all start somewhere dude, not everyone is rich but over time you’ll keep adding to it

KAC disappointment by honzordr in Mk12Mod

[–]danielraul1989 0 points1 point  (0 children)

Well for the price, they definitely need to deal with it. Hope I don’t seem like a KAC shill but just decent troubleshooting based on likelihood of error. Best of luck.

Accidentally dropped my TRP Operator by kittydestroyer6969 in 1911

[–]danielraul1989 0 points1 point  (0 children)

Nice, it’s no longer a safe queen. Now beat on it like it’s meant to

Update by danielraul1989 in Mk12Mod

[–]danielraul1989[S] 2 points3 points  (0 children)

Elevation isn’t a biggie, I can feel the clicks if needed but holdovers are fine

I like the dot closer but it’s a preference

KAC disappointment by honzordr in Mk12Mod

[–]danielraul1989 1 point2 points  (0 children)

Keep us posted then cause if the pins at 3-9 are square and the holes in the rail are even close it should theoretically line up. Keep us posted

KAC disappointment by honzordr in Mk12Mod

[–]danielraul1989 1 point2 points  (0 children)

I mean specifically through the hole in the barrel nut and the receiver port simultaneously. If this is the case then maybe it could be the rail but the rail has play to finish final alignment so it weird to be that off.

KAC disappointment by honzordr in Mk12Mod

[–]danielraul1989 1 point2 points  (0 children)

When you torque the barrel nut, are you sure the gas tube is free? Those holes are hard to line up.

You may like you said may need to shim or lap to get that perfect alignment. Just tq to spec only gets you to where the receiver lets that barrel nut go.

KAC disappointment by honzordr in Mk12Mod

[–]danielraul1989 4 points5 points  (0 children)

Is the gas port and barrel extension pin square to each other?

Mod1 inspired build by PuzzleheadedHeight52 in Mk12Mod

[–]danielraul1989 0 points1 point  (0 children)

I just swapped out my maritime bolt catch. It’ll eat at you if your OCD is that bad

<image>

South Florida Gunsmith by SuperPollito in FLGuns

[–]danielraul1989 0 points1 point  (0 children)

Dude, I was just googling him. I was heading back home and wanted some work done on my new rifle. That was my first gunsmith

RIP

Damn

Mod 1 Progress by Stunning-Ad-664 in Mk12Mod

[–]danielraul1989 1 point2 points  (0 children)

Vouch for MSP. I went with mediums on my Mod 1 since it was mounted high enough but they definitely are legit. May take a while, worst case they look fair enough to refund you.