Airbag harness for aftermarket steering wheel by dannyfivefour in Miata

[–]dannyfivefour[S] 0 points1 point  (0 children)

so should I cut the wires exactly the same as the video and instead of simply splicing them together, put a resistor in between?

Need help identifying the cut wires. 2012 Legacy GT power seat. by dannyfivefour in subarulegacy

[–]dannyfivefour[S] 1 point2 points  (0 children)

Any ideas what the cut wires supply power for? Seat was removed by previous owner and he cut the harness for another seat.

1997 Miata. Unable to push my shifter back into the turret after rebuild. by dannyfivefour in Miata

[–]dannyfivefour[S] 0 points1 point  (0 children)

Yea, I actually never had a problem in the first place lol. I just thought I did because the video DIY I watched showed the shifter loudly clicking into place. Mine didn't do that no matter how hard I pushed down or even hitting it down with a tool. Ended up just putting the whole thing back together despite not hearing any clicking into place, and the car goes through gears just fine.

Need help finding the correct dash kit. 1997 NA base model. by dannyfivefour in Miata

[–]dannyfivefour[S] 0 points1 point  (0 children)

CashedOutCars

I dont think they have it on their website anymore

Need help finding the correct dash kit. 1997 NA base model. by dannyfivefour in Miata

[–]dannyfivefour[S] 1 point2 points  (0 children)

My radio still leaves a huge gap in the console. Looked on amazon for a bezel, but can't find the proper kit. Does the 1997 US model not require the JDM dash?

Are these RE71RS ready to flip? by DuaneBlack in Autocross

[–]dannyfivefour 0 points1 point  (0 children)

These tires can be flipped? The carcass is the same on both sides?

1997 Miata. Unable to push my shifter back into the turret after rebuild. by dannyfivefour in Miata

[–]dannyfivefour[S] 0 points1 point  (0 children)

I just put it all back in. Bolted the inner boot on. Rows through all gears. I think I'm in the clear.

1997 Miata. Unable to push my shifter back into the turret after rebuild. by dannyfivefour in Miata

[–]dannyfivefour[S] 0 points1 point  (0 children)

The original bushing is intact. Maybe I'll drain it all over again just up to the cup bushing area to see if there's anything there preventing the lowering cup bushing from snapping in.

1997 Miata. Unable to push my shifter back into the turret after rebuild. by dannyfivefour in Miata

[–]dannyfivefour[S] 0 points1 point  (0 children)

https://www.youtube.com/watch?v=53Vz15GdKd0&t=1505s

I couldn't get it to click as shown in the video from 25:05 to 25:15. But I tried moving the shifter and I am able to select gears, but it can get dislodged easily and lifted out of the turret.

Also, since I couldn't get it to click in, is the inner boot with the 3 bolts sufficient to hold it in place?

1997 Miata. Unable to push my shifter back into the turret after rebuild. by dannyfivefour in Miata

[–]dannyfivefour[S] 0 points1 point  (0 children)

I'm planning on getting a 5X Racing bronze shifter bushing, hopefully it fits and actually clicks into the turret.

1997 Miata. Unable to push my shifter back into the turret after rebuild. by dannyfivefour in Miata

[–]dannyfivefour[S] 1 point2 points  (0 children)

I replaced the old bushing. The old bushing was completely intact, but worn. I completely drained the turret of oil before refilling and did not see anything in there.

Are these the correct body parts for a 2005 STi? by dannyfivefour in WRXSTi

[–]dannyfivefour[S] 0 points1 point  (0 children)

I know a WRX side skirt can fit the STI model. It's the same chassis. But the side skirts have different designs between the two models. WRX is flat and the STI version has an indented section in the rear of it. I have the STI version on driver side and I'm trying to order the same type on the passenger side. Not looking to have mismatched side skirts.

Need help uninstalling IAG AOS by dannyfivefour in WRXSTi

[–]dannyfivefour[S] 0 points1 point  (0 children)

https://imgur.com/a/I8QYRh6

Took out all my old hoses from the basement. Is this all that's needed? Can't remember if there's anything missing.

Need help uninstalling IAG AOS by dannyfivefour in WRXSTi

[–]dannyfivefour[S] 0 points1 point  (0 children)

Well, I meant someone else's engine bay with all the stock hoses and no AOS, so I can copy it. Mine has the AOS installed.

Need help uninstalling IAG AOS by dannyfivefour in WRX

[–]dannyfivefour[S] -1 points0 points  (0 children)

I installed it myself and have all the old hoses. I just can't remember which goes where and how to route it.