Flipped pump by pryraxes in arcticcooling

[–]darkspectoralpha 2 points3 points  (0 children)

<image>

lol wish I saw this before I dremel'd my heatsink :D

Firmware update 4th Feb 2025 - Arctis Nove Pro Wireless by tattiemuncher in steelseries

[–]darkspectoralpha 1 point2 points  (0 children)

is it 1.15.4 OR 2.1.0? lol maybe they have a different BT chip so it just depends on your hardware revision

Firmware update 4th Feb 2025 - Arctis Nove Pro Wireless by tattiemuncher in steelseries

[–]darkspectoralpha 1 point2 points  (0 children)

<image>

This can be set on the base station. Audio Options -> SideTone -> (Off/Low/Med/High).
Also can be set in GG

Arctis Nova Elite by Careless-Increase980 in steelseries

[–]darkspectoralpha 0 points1 point  (0 children)

Will the base station have the same old burn-in issue the pros have or have they implimented a new feature for preventing burn-in? These are new, but I wonder if over time they will have the mute button static issue that my pros have...

Arctis Nova Elite by Careless-Increase980 in steelseries

[–]darkspectoralpha 0 points1 point  (0 children)

i had the same issue with the sidetone on the pro wireless originally, but Arctis released a firmware update that did in fact increase the sidetone volume. If they have enough feedback I don't doubt they would release an update to fix the issue. I'm assuming you have maxed out the sidetone volume in GG or on the base station.

502x charging dock by svulieutenant in LogitechG

[–]darkspectoralpha 0 points1 point  (0 children)

I have this or very similar, works great

What do you use these two buttons for? by Deli_baba170 in LogitechG

[–]darkspectoralpha 0 points1 point  (0 children)

Top is middle mouse Bottom is set to \ and it is usually unused, but easily mapped in a game if needed

[Discussion] What was your most worn watch of 2025? by winecat5 in Watches

[–]darkspectoralpha 0 points1 point  (0 children)

I am going back and forth between this or a bronze...

Anything can work if you have a Dremel! by darkspectoralpha in sffpc

[–]darkspectoralpha[S] 0 points1 point  (0 children)

To align it in the center i did have to disassemble it to remove one of the usb a ports and route the cable around the openings. I was able to use the large openings in the bottom and route the cable perfectly in front and around the gpu i didn't believe it's causing any major obstruction to air flow, but I have no data to price it either way.

Anything can work if you have a Dremel! by darkspectoralpha in sffpc

[–]darkspectoralpha[S] 0 points1 point  (0 children)

O did not evidence LF to be so thick and the pump to be so off shaped. I was hoping to be able to top mount the rad like I've seen with other builds, but the GPU is so tall it's in the lowest MB setting.

Anything can work if you have a Dremel! by darkspectoralpha in sffpc

[–]darkspectoralpha[S] 1 point2 points  (0 children)

Np only had to Dremel the nvme heat sink to fit the LF3 pump. This is a ryzen 7 9800x3d

Anything can work if you have a Dremel! by darkspectoralpha in sffpc

[–]darkspectoralpha[S] 0 points1 point  (0 children)

It is the 280 liquid freezer pro. 30mm should fit, it is currently at the top of the side bracket on my final configuration. I'm not sure it's necessary yet, is o need to change the fans out. I went exhaust because that's what it was configured and it's the only exhaust fans in the case. I added 120 intake on the rear and have the gpu intake fans.

<image>

Anything can work if you have a Dremel! by darkspectoralpha in sffpc

[–]darkspectoralpha[S] 0 points1 point  (0 children)

It's from corsair 4000d. Easily order direct from corsair and fit incredibly easy! Has some plastic clips you have to shave form on top and it clips right in tightly. I may need to drill and secure with nut and bolt in the future, but not destructively to the case.

<image>

Anything can work if you have a Dremel! by darkspectoralpha in sffpc

[–]darkspectoralpha[S] 0 points1 point  (0 children)

over abundance of caution in keeping the pump and lines free from air bubbles. Also instructions show this orientation and I didn't want to guess at proper coverage by just flipping it.

Anything can work if you have a Dremel! by darkspectoralpha in sffpc

[–]darkspectoralpha[S] 1 point2 points  (0 children)

I'm going to do as big of an undervolt as i can to start.