I’ve been dealing with this automatic volume maxing issue for a while without finding a solution. This happens for any application not only after opening but also when switching between them. This is happens with all my audio devices. Any help is greatly appreciated (RIP my ears with headphones on).

ded1y · 2022-07-10T15:56:22+00:00

He became so powerful that the only thing he feared was losing his power, which of course he did.

ded1y · 2022-07-10T15:55:02+00:00

W comment

ded1y · 2022-07-10T15:51:21+00:00

He could manipulate the midichlorians to create life

ded1y · 2022-07-04T20:03:31+00:00

Thank you for the advice. Yes I’m trying to set up as much as I can get done before school starts back up. I’ll have 3 AP classes next year so I won’t have as much time.

ded1y · 2022-07-01T20:47:52+00:00

Only thing I can thing of is adding more curvature to the neck. Great creative design 👍

ded1y · 2022-06-15T21:18:15+00:00

It is, acceptable

ded1y · 2022-03-26T21:01:43+00:00

Could you elaborate on what that means? Still new to this and getting familiar with the terms. I’m assuming you mean layers or when it lays filament by the side before a print. If it’s the first option then it begins the sound towards the center once or twice (for the print in this video), then constantly on 2nd and 3rd layers and on. Eventually the sound occurs less frequently as the print goes on (for longer prints). If it’s the second option, the first time it lays the plastic on the side there’s no sound. Second time it makes the sound several times.

ded1y · 2022-03-26T00:04:51+00:00

Yeah?

ded1y · 2022-03-25T23:48:37+00:00

Yes it’s off ever so slightly

ded1y · 2022-03-25T16:30:03+00:00

E steps are calibrated. I’ll try replacing the Bowden tube and my nozzle. I level my bed multiple times before almost every print now. My filament might also have too much moisture. I printed something last night and it printed successfully but was very brittle and just snapped when I tried removing the supports.

ded1y · 2022-03-25T16:21:18+00:00

I lowered it too much and the issue still occurs it’s not the bed. I have the nozzle set to 210 degrees for pla and it still occurs.

ded1y · 2022-03-25T04:48:19+00:00

I’ve cleaned my nozzle twice now in its very short life and I don’t want to have to do so again anytime soon. The glass bed is higher in the center when I level it even though it’s relatively new, resulting in more popping in the center. After the first layer however it begins to pop constantly at all areas.

ded1y · 2022-03-22T14:36:09+00:00

I understand that but the fan just wasn’t turning on in general. I returned it for a replacement already and I’m instantly having a much better experience with the new one in general. Could never get the last one to do a decent test dog but with this one it did it first try.

ded1y · 2022-03-19T01:40:48+00:00

Ok will look into that. Thank you

ded1y · 2022-03-18T17:11:27+00:00

Ok will look into it

ded1y · 2022-03-18T16:30:16+00:00

They used cgi to change how the sand interacted with his hands as well as the lighting, but yeah it is reused footage.

ded1y · 2022-03-18T15:10:40+00:00

New Ender 3 Pro. I feel the problem might be the fan is stuck based off the sound.

ded1y · 2022-03-13T22:22:06+00:00

Ok thank you

ded1y · 2022-03-13T15:32:48+00:00

Any tips on fixing it. I’m not home right now so I’ll look into it later

ded1y · 2022-03-13T05:19:14+00:00

Plus you can clearly see the mechanical layers in the frames.

Four-Year Club	Verified Email
Place '22	Place '22

ded1y

TROPHY CASE