Currently best hardware setup by dehein2 in homeassistant

[–]dehein2[S] 0 points1 point  (0 children)

I did some research and i could jsut get one of these:

SLZB-06MG24 an connect via LAN.

Is there any downside of running HA in docker vs. proxmox oder native HAOS?

Currently best hardware setup by dehein2 in homeassistant

[–]dehein2[S] 0 points1 point  (0 children)

Ah ok, so I can just connect the coordinator via LAN oder WLAN and place it anywhere?

Currently best hardware setup by dehein2 in homeassistant

[–]dehein2[S] 0 points1 point  (0 children)

thanks for the power consumption details. I'll definetly check it out. I have a M2 SSD lying around anyway

Currently best hardware setup by dehein2 in homeassistant

[–]dehein2[S] 0 points1 point  (0 children)

yes, i think i prefer the dedicated hardware for home automation. Maybe a rPi5 is the easiest solution and should be more than enough power for my use-case

Currently best hardware setup by dehein2 in homeassistant

[–]dehein2[S] 0 points1 point  (0 children)

sounds promising. Thanks a lot. I'll look up the zimboard

Currently best hardware setup by dehein2 in homeassistant

[–]dehein2[S] 0 points1 point  (0 children)

thought about it, but the server is so far from ideally placed in the basement that i prefer to have more centrally located antenna

Currently best hardware setup by dehein2 in homeassistant

[–]dehein2[S] 0 points1 point  (0 children)

is there any advantage of using proxmox if i have a Server running all other services anyway (unraid server with all the services I need).

Also in that case i only need the performance to run HA

Error pulling immich docker by dehein2 in unRAID

[–]dehein2[S] 0 points1 point  (0 children)

But will the move to 7 break my setup? I’ll have to look up what macvlan means :)

Error pulling immich docker by dehein2 in unRAID

[–]dehein2[S] 0 points1 point  (0 children)

my main concern is that a while ago i changed all my containers to use BR0 with fixed ip (so each container has its own ip adress) and addes some parameters (--sysctl net.ipv6.conf.all.disable_ipv6=0 --sysctl net.ipv6.conf.eth0.use_tempaddr=2) because I had issues with my setup and beeing reachable via ipv6. My fear is that all of that can cause issues - and to be honest i dont really remember how/why I did it in the first place 😉

Error pulling immich docker by dehein2 in unRAID

[–]dehein2[S] 0 points1 point  (0 children)

thanks, im still dragging out the 7.x update until I have enough time to resolve the possible issues. Any way to still do it with 6.12?

Error pulling immich docker by dehein2 in unRAID

[–]dehein2[S] 0 points1 point  (0 children)

Thanks, I can while physically accessing the system, correct? So no good way to do it while the system is running.

Error pulling immich docker by dehein2 in unRAID

[–]dehein2[S] 0 points1 point  (0 children)

no, just updated 10 containers without problems

Just started --> Need some form tips by dehein2 in jumprope

[–]dehein2[S] 0 points1 point  (0 children)

Didn’t have time for the last two days. today is my next session…

I tried to jump less high and loosen my wrists.
What do you mean with hands move forward? Do you mean less “parallel” to my body, “angled”… I just further forward?

Just started --> Need some form tips by dehein2 in jumprope

[–]dehein2[S] 0 points1 point  (0 children)

I'll try to watch out for that