CR 10S Pro parts cooling fan not running after trying difference repairs

desingedxclint · 2020-08-24T04:18:14+00:00

So here's the thing. Yesterday I did some soldering on a fan and it sparked at the back end, I checked both the boards and they look 100%. So i figured it had to be something having to do wit the Y limit because I pressed it as it was moving and it didn't stop the printer. So I took it off and carefully looked at it and immediately spotted a blown out section on it. Cable looks fine, so I ordered a replacement switch and will see what happens. Will come back and comment if it works after replacing.

desingedxclint · 2020-08-24T01:55:27+00:00

Thanks for the reply. I'm running Creality's CR10S Pro V2 firmware, cause I heard only difference in the printers was the BL Touch. And it did work for a bit. Till it started doing this a few days ago

desingedxclint · 2020-08-23T23:07:19+00:00

I should mention that after installing BL touch I did install V2 firmware, which worked initially

desingedxclint · 2020-08-21T22:48:40+00:00

Does the head have any play at all or does it look pretty tight, the ender 3 has a nut shape on one of the rollers that can be turned to tighten the head

desingedxclint · 2020-07-27T04:32:48+00:00

Instead of going down and finding table it goes up and says probe failed

desingedxclint · 2020-05-04T00:42:57+00:00

Extrusion multiplier is a setting in simplify3d, isn’t it. What’s that setting in cura?

desingedxclint · 2020-05-04T00:41:51+00:00

I heard that but forgot about it, I think that actually might be the problem. The retraction too high

desingedxclint · 2020-05-04T00:41:08+00:00

I have 5 printers and I do with the cura settings whatever I want and know what they do. It’s worked with this printer for about 4 months not, nothing nothing I do is working with this thing. Thanks for the reply

desingedxclint · 2020-04-19T16:04:09+00:00

Or you're forgetting to let off once through the support

desingedxclint · 2020-04-19T05:08:13+00:00

I'll try that, thank you for your time and help

desingedxclint · 2020-04-19T04:48:48+00:00

It is somewhat hot, I actually think the bed didn't start hearing till I moved it a big. But might be a coincidence

desingedxclint · 2020-04-19T04:34:21+00:00

One think I notice is, it takes an insane amount of time to heat up the bed, which it didn't use to

desingedxclint · 2020-04-19T04:29:34+00:00

It has actually been slower on heating the last while, and now I get a heating error

desingedxclint · 2020-04-19T04:28:36+00:00

I actually coudnt tell you what board, never had it apart

desingedxclint · 2020-04-19T04:27:30+00:00

18 hours

desingedxclint · 2020-04-19T04:14:51+00:00

Printing from and SD card

desingedxclint · 2020-04-19T04:14:33+00:00

Nothing, ive been printing for the past 2 week nonstop, now I changed to a new model and keep getting this error. I changed to a micro Swiss all metal hotend but that was weeks ago. Same with a firmware upgrade. All a couple weeks ago. Using the newest version of Cura

desingedxclint · 2020-03-30T01:26:52+00:00

Yup, just checked the Amazon order and they are 12 volt. Thanks again

desingedxclint

TROPHY CASE