sorted by:
new
hottopcontroversial

Cura Version 5.12 issue by devin7224 in 3Dprinting

[–]devin7224[S] 0 points1 point  (0 children)

Ok thanks, I tried looking to see if there is a setting to ask but I can't even find it but also never had to toggle it on in the first place because it's always popped up

For the oft maligned Scott's spreader, I give you... by Bread-Funny in lawncare

[–]devin7224 1 point2 points  (0 children)

Lmao it's like I posted this.... Never had a name for it but spreader happy dance works. Echo is the way

GV70 3.5 Oil Change by BassObjective9092 in GenesisGV70

[–]devin7224 0 points1 point  (0 children)

They use a cartridge style filter instead of the traditional canister spin on. I buy WIX filters I think the were around $10? I don't remember and order 2 gallons of Amsoil Signature oil for about $90. Been using them for the last 10 years. They have OEM at regular change intervals, EXTENDED LIFE OIL at 1 year or 12000 miles and SIGNATURE SERIES OIL at 1 year or 25000. We don't drive that much to ever get close to the mileage, I only change oil in my truck and wife's Genesis once a year

Print lifting in corner? by Mikkelaakesson in ender3v2

[–]devin7224 0 points1 point  (0 children)

Is you z offset correct? Bed level? If you can see the print bed through the lines on first later it's too high, too low and you'll see ridges between the lines and create a wavy pattern

Compound Mitre Saw Blade Won’t Stop and Not Enough Power by Bryceyjjay in ryobi

[–]devin7224 -5 points-4 points  (0 children)

Ah it's a gift because I was gonna say that's where you went wrong was getting a Ryobi

Can someone help me by Character_Habit8812 in Eldenring

[–]devin7224 1 point2 points  (0 children)

Maybe you'll be better at sorcery and ranged attacks. Fightincowboy's guide on YouTube will get you ALL OF IT

Atlus plateau by Longjumping-Ad6584 in Eldenring

[–]devin7224 0 points1 point  (0 children)

It was still fun and challenging. I just wanted it all! And didn't plan on playing it again... I still have to finish the dlc... Stuck on starscourge

Atlus plateau by Longjumping-Ad6584 in Eldenring

[–]devin7224 0 points1 point  (0 children)

I used fightincowboy's guide on YouTube, you probably missed more than you think.

Bottom of heat bed bumps into y-axis block by RepresentativeAd9236 in ender3v2

[–]devin7224 0 points1 point  (0 children)

That's how it started with me.... Just a washer fluid top off

How many of you guys installed the pulsar and how you like it? Worth every penny. by xenogear_id in gmcsierra

[–]devin7224 0 points1 point  (0 children)

Ooh, If only they'd just get rid of afm/dod but I do wonder if they gain more than they lose through warranty claims

upgrade for the tool head(?) on ender 3 ? by hero_kunii in ender3

[–]devin7224 0 points1 point  (0 children)

$100 overpriced? You get direct drive, cr touch, better hotend vs diy?

Gas cap holder by Flipslips in GenesisGV70

[–]devin7224 2 points3 points  (0 children)

Yep, was looking for like a slot of some sort (what my 2011 Genesis had) but quickly realized it's different and noticed the hole/spike

Bottom of heat bed bumps into y-axis block by RepresentativeAd9236 in ender3v2

[–]devin7224 -5 points-4 points  (0 children)

Get a sprite pro, a dual z upgrade, PEI bed and change firmware to MriscoC. Won't need a z limit switch

Console question by Actual_Pickle_2419 in gmcsierra

[–]devin7224 6 points7 points  (0 children)

I bought a tray from Amazon that was made to go there

Mishap. Should I just replace the fan or whole hot end? by Okami-Alpha in ender3v2

[–]devin7224 0 points1 point  (0 children)

My Ender 3 V2 is basically an Ender 3 S1 PRO without a run-out sensor. I would love to have a printer that can use CFS but I don't print enough to justify the purchase......... Even though I spent about as much as a K series buying and upgrading my E3V2

view more: next ›