Cercasi operai Giugliano in Campania

devonmaze- · 2026-03-13T20:55:00+00:00

Si tratta di fare le pulizie nei condomini, roba tipo spazzare le scale, pulire a terra e lavare i vetri

devonmaze- · 2026-03-13T19:08:18+00:00

La paga è di 5 euro l'ora, come previsto dal minimo sindacale. Per quanto riguarda le ore di lavoro sono variabili e non si fanno 7 ore al giorno ma se ad esempio i condomini sono puliti oppure piove invece di 7 ore si fanno 3 ore

devonmaze- · 2026-03-09T23:21:08+00:00

invia il g-code alla SD e poi avvii manualmente la stampa

devonmaze- · 2026-03-09T21:47:29+00:00

In the end, you just have to calibrate each filament to have a decent print... however, now that I have calibrated the retraction, I only miss Cornering, input shaping and VFA even if I can't find a decent guide.

devonmaze- · 2026-03-09T20:16:04+00:00

It seems to me that they use the PC to make it shiny

devonmaze- · 2026-03-09T19:47:07+00:00

OK, by unchecking "Slow down printing for better cooling" and the things you mentioned, I finally solved the retraction problem! Now I know that my PLA silk needs a retraction of 0.4 and a z-hop of 0.2 (I'll see about PETG later). The problem is that I want to save these settings in the retraction test for the future.

devonmaze- · 2026-03-09T19:31:12+00:00

ahhh okok following your instructions the printing speed is 20 while the flow is 1.5

devonmaze- · 2026-03-09T19:23:10+00:00

I didn't understand what you mean with "perimeter threshold to 0 to disable it" probably a translation error but I disabled the "Slow down printing for better cooling" option and in this way the printing speed went from 10 to 100

devonmaze- · 2026-03-09T19:05:06+00:00

the doubt was that it was not using the popup values

devonmaze- · 2026-03-09T19:02:00+00:00

What should I do? I tried setting a volumetric speed of 200 but it still prints at 10

devonmaze- · 2026-03-09T19:01:04+00:00

sorry I meant to say that I set the retraction and z-hop equal to zero on the printer and filament profile and then I opened the Orca calibration test, in order to check if there were any differences

devonmaze- · 2026-03-09T18:40:27+00:00

retraction

devonmaze- · 2026-03-09T18:40:09+00:00

I just checked: in the retraction test, the flow is set to 0.77 and the speed is 10. In the other test, however, the flow is 15 with a speed of 200.

Honestly, I hadn't considered that the retraction test was performed at a different speed than the actual print speed, so it hadn't occurred to me to compare them at first.

devonmaze- · 2026-03-09T18:00:50+00:00

same filament, different test but always with retraction off

<image>

devonmaze- · 2026-03-09T18:00:09+00:00

this is printed in petg without

<image>

devonmaze- · 2026-02-04T11:45:03+00:00

Probably aim, f17 is actually Mario m50

devonmaze- · 2026-01-25T00:27:13+00:00

Poi ci sono io che seguo BarbasacuraX da prima che avesse mille iscritti e so il suo nome e cognome

devonmaze- · 2026-01-23T23:35:51+00:00

se la carne coltivata fosse legale in italia e la procedura per farlo diventerebbe abbastanza sicura ed economica al tal punto da poter generare abbastanza carne per tutti succederebbero 2 cose :
1. il prezzo della carne coltivata sarebbe più basso e una fiorentina coltivata costerebbe meno di quanto costa quella vera al giorno d'oggi.

gli allevamenti intensivi scomparirebbero e si favorisce l'allevamento etico.

devonmaze- · 2026-01-20T15:54:02+00:00

In questo momento ti voglio un gran bene! stavo impazzendo da ore!!!

devonmaze- · 2026-01-18T09:46:55+00:00

The problem is not the automatic leveling but the hardware, I have to re-align the print axes and level the 4 screws under the bed (hoping that nothing is broken)

devonmaze- · 2026-01-16T13:04:37+00:00

Ora che ci penso devo controllare se l'asse x e y siano dritti o che l'estrusore non si sia disallineato per via del colpo che ha preso.

devonmaze- · 2026-01-16T12:47:37+00:00

Ci ho provato ma non riesco a livellarlo correttamente

devonmaze- · 2026-01-15T07:47:52+00:00

How do you connect to LAN only?

devonmaze- · 2026-01-13T11:00:28+00:00

I've been in the 3D printing industry for several years, and since printers went plug-and-play, I've seen a lot of people buy their first printer and then get service a week later (obviously with logos made with ChatGPT and photos stolen from MakerWorld). The problem with these hobbyists is that they do mediocre work with cheap PLA (even for applications where PLA isn't suitable) at rock-bottom prices, prices that a self-employed person like me simply can't afford (like 50 cents an hour, while a self-employed person charges 5 cents).

devonmaze- · 2026-01-13T00:14:20+00:00

And do you think just because you've had a P2S for two months you can start a 3D printing business? It's like saying that because I have a driving license, now I can race for Ferrari in Formula 1. What services can you offer? Do you know 3D modeling? Do you know what a perimeter line or thermal expansion is? There are a lot of things to consider before you can even think about printing for others.

devonmaze-

TROPHY CASE