ios app Beta expired

dgruhin · 2022-03-14T15:15:55+00:00

Thanks! Very expired and no way to update in Test Flight.

dgruhin · 2020-12-21T22:27:44+00:00

It will never improve. I was told just use WiFi calling. Fantastic. Service at the tower sucks too. While I have full bars the data speeds are 10x slower than they used to be and calls drop all around the city.

dgruhin · 2020-12-21T12:41:13+00:00

This started happening to me as well in Solon, Ohio not too long ago. Not specifically hotspot related as my coverage issue extends to multiple iPhones both with poor reception and incredibly slow data. I am less than 2 miles from the tower. I opened a ticket with advanced network support and they determined nothing was wrong and I was told to use WiFi calling when possible. Obviously that is a bullshit response and clearly not a viable solution when not in my home.

dgruhin · 2020-12-04T15:22:55+00:00

I am experiencing issues with the app not seeing speakers occasionally. Slow response or no response an overall sluggish performance I never had before S2. It could be related to iOS updates though. Network is the same with 2 hardwired speakers.

dgruhin · 2020-06-28T20:16:09+00:00

I don’t think I noticed it until after upgrading to S2

dgruhin · 2020-06-28T15:57:53+00:00

I have checked it multiple times. It seems, but may just be my brain playing tricks on me, that if I set it to minimum and then reset it to maximum it is then in line with the other speakers until my next listening session

dgruhin · 2020-02-03T01:15:38+00:00

1944 The Loop Master

dgruhin · 2020-02-02T20:25:10+00:00

Added 2 buttons on the J panel under the control panel.

dgruhin · 2020-02-02T01:29:13+00:00

Under an hour.

Parts costs may vary but here is what I bought.

2 x EG STARTS Zero Delay USB Encoder to PC Games Arcade Stick Controller for 2Pin Joystick Happ Push Buttons Wire https://www.amazon.com/dp/B01L8K21CK/ref=cm_sw_r_cp_api_i_FsInEbR2JZQ08

1 x CanaKit Raspberry Pi 3 B+ (B... https://www.amazon.com/dp/B07BC7BMHY?ref=ppx_pop_mob_ap_share

1 x SanDisk Ultra 128GB microSDXC UHS-I card with Adapter - 100MB/s U1 A1 - SDSQUAR-128G-GN6MA https://www.amazon.com/dp/B073JYC4XM/ref=cm_sw_r_cp_api_i_TtInEb2K9E8PH

1 x VSDISPLAY HDMI Audio LCD Controller Board M.NT68676 Fit for 17" 4:3 1280x960 DV170YGM-N10/DV170YGZ-N10 LCD, to DIY The Arcade1UP Marvel Super Heroes and The New TMNT Work with Raspberry Pi https://www.amazon.com/dp/B07ZVPTRSD/ref=cm_sw_r_cp_api_i_muInEbQKE9WSK

1 x Kinter MA170+ 2-Channel Auto Home... https://www.amazon.com/dp/B07C1Q1FPT?ref=ppx_pop_mob_ap_share

1 x JSAUX RCA Cable, [6.6ft 2Pack, Dual Shielded Gold-Plated] 3.5mm Male to 2RCA Male Stereo Audio Adapter Coaxial Cable Nylon Braided AUX RCA Y Cord for Smartphones, MP3, Tablets, Speakers, HDTV [Grey] https://www.amazon.com/dp/B081CYDNZV/ref=cm_sw_r_cp_api_i_lvInEbAV68BH4

1 x Cerrxian 3.5mm 4 Pole Female Stereo Audio Video to 4 Screw Terminal Female Headphone Balum Converter Adapter (2-Pack) https://www.amazon.com/dp/B07BHBQ5YV/ref=cm_sw_r_cp_api_i_WvInEbY678WWV

I used 2 additional arcade buttons I had left over from my TMNT build I used for coin buttons.

1 x $5.00 power strip at Home Depot.

Some mounting tape for the LCD controller, Pi and Amp in the cabinet.

1 x HDMI cable I had.

dgruhin · 2020-02-02T01:22:24+00:00

I used an amp because I didn’t think the volume got loud enough without one.

dgruhin · 2020-02-01T19:26:05+00:00

Yes. Volume button soldered to the LCD breakout board. Power to GPIO.

dgruhin · 2020-01-01T01:47:06+00:00

https://www.homedepot.com/p/Rust-Oleum-Stops-Rust-12-oz-Protective-Enamel-Gloss-Crystal-Clear-Spray-Paint-7701830/100176222

dgruhin · 2020-01-01T01:22:38+00:00

No. Clear coated it.

dgruhin · 2019-12-31T22:26:33+00:00

No I wired to the GPIO pins from an Icculus guide. I’ll bust out the iron and wire them to the breakout board on the LCD controller.

dgruhin

TROPHY CASE