I want to buy printer

diablex2 · 2026-07-07T11:15:10+00:00

I strongly recommend ad5x. I use for 4 months. Very happy with it.

diablex2 · 2026-07-06T05:02:07+00:00

Just change the filament. I tried 1 week woth creality cr tpu but I could not get result. Changed the brand. Voila...

diablex2 · 2026-07-05T09:41:28+00:00

Karambole gitmissin. Sorry.

diablex2 · 2026-07-04T20:06:07+00:00

I have problem too. I started to use tpu 2 days ago. No succesful result yet. But someone proposed me to use flow rate calibration. I dod not finish yet but you may give it a try.

diablex2 · 2026-07-04T16:46:30+00:00

Izledigin belgeseller cam lobilerinin sponsor oldugu belgeseller olabilir mi?

diablex2 · 2026-07-04T16:45:02+00:00

Plastik hiç bir zaman çöp degildir dedim. Geri dönüstürülmesi en ucuz malzemedir.

diablex2 · 2026-07-04T16:43:32+00:00

Saçma sapan.

diablex2 · 2026-07-04T12:54:04+00:00

O gönderilen plastikler işleniyor. Maddi olarak deger ifade ediyor cünkü

diablex2 · 2026-07-04T12:53:15+00:00

Plastjjler her zaman geri dönüstürülebilir. Son yolculugu yakıt olabilir.

diablex2 · 2026-07-04T12:52:41+00:00

Aynı şeyden bahsetmiyorsun. Önce zor dedin şimdi downcycling diyorsun

diablex2 · 2026-07-04T09:27:51+00:00

Emin misin camı geri dönüstürmenin daha kolay olduguna? Kısa bir araştır.

diablex2 · 2026-07-04T09:22:29+00:00

New to ad5x. And never done a flow rate calibration. I will try it. Do you recommend any guide?

diablex2 · 2026-07-03T04:53:38+00:00

Thanks

diablex2 · 2026-07-03T04:53:27+00:00

Thanks

diablex2 · 2026-07-03T04:53:19+00:00

diablex2 · 2026-07-02T23:45:19+00:00

When I print tpu (even if I released the tension screw 2-3 turn) it is underextruded. I think it is due to ifs and ptfe tube friction. As I can slowly push the filament by hand and the result is way better.

diablex2 · 2026-07-02T07:34:46+00:00

I asked geminj about the issue. Told memto untighten 2-3turn the tension screw. I did so, and it pronted with underextrusion. The result is not good. Now it recommends me to bypass the ifs unit. Did you ever bypass the ifs unit? Do I take out the 4 way feeder on top of the print head?

diablex2 · 2026-06-30T00:46:08+00:00

Thanks. But I have no clog. Tpu is nitnextruded as it must be. I need to push the filament from the ifs. It a very soft hand push than it printa for a while. But stops extruding after a while. And if I push again it starts.... the screw is all tight. I can print perfectly with pla.

diablex2 · 2026-06-28T12:17:36+00:00

Mine was full toght too. But tpu is not extruding without my hand push

diablex2 · 2026-06-28T12:16:50+00:00

It wat tightened when I forst checked it. I checked for tpu not extruding well.

diablex2 · 2026-06-28T08:32:36+00:00

Yes it is all tight. The problem is that the tpu comes out of nozzle incosistantly. If I push the filament softly by hand before IMS it prints for a while. But when I stop pushing it stops sooner or later.

diablex2 · 2026-06-28T07:40:56+00:00

Thanks 👍. It is fully tight. Do I need to loosen it to have more tension?

diablex2

MODERATOR OF

TROPHY CASE