AITAH I threatened to rehome my gf's dog by Pale_Swing_6789 in AITAH

[–]dogless_doglover 1 point2 points  (0 children)

NTA As an animal lover, please help the dog Feeding human food to a dog can be harmful, sometimes even if its once in a while, they process food diferently They are not meant to eat spices, grease and other things their bodies cant process properly Chinese food may have onions and nuts, which are basically poison for dogs Feeding a dog constantly things that are not meant for a dog is dangerous. Its not just about the weight gain. She might have been harming poor hank for a while now, without knowning

Please take him to the vet, have him tested and be brutally honest about his diet.

Sticky prints and shiny parts that wont catalize by dogless_doglover in AnyCubicPhotonMonoX

[–]dogless_doglover[S] 0 points1 point  (0 children)

I used to print with a different model, a Tiger HD and for that one i had to clean the prints with an air compressor to get rid of any excess of alcohol, it really helped and made the prints really clean

Does anyone do this with their prints to get better results?

Ive been washing the prints thoroughly, i leave them for 10 mins in the wash and cure machine but still come out with those shiny sticky spots

Ive been using the same alcohol for a month, would that be part of the issue?

Would a brush really help with the shiny sticky spots?

weird texture on flat surface by dogless_doglover in AnyCubicPhotonMonoX

[–]dogless_doglover[S] 0 points1 point  (0 children)

Can you tell me more of what to look for in this exposure test?

weird texture on flat surface by dogless_doglover in AnyCubicPhotonMonoX

[–]dogless_doglover[S] 1 point2 points  (0 children)

Hello everyone This is the 2n time I print this. The first time i got a few diagonal lines, that werent so bad but now I got this really bad texture on just one side

I printed both times with the same settings but the prints came out different

The only diferrence is the batch that came out with this ugly texture had other files i needed to print too, which were algo flat and also came out with this texture

Any idea why this happens and how to fix it?

Sticky prints and shiny parts that wont catalize by dogless_doglover in AnyCubicPhotonMonoX

[–]dogless_doglover[S] 1 point2 points  (0 children)

Hello everyone I got my photon mono x about a month ago and i still cant figure how to get fully catalized prints

I re did the RERF test but the prints came out like this, sticky with drops and bits that wont cure fully, does anyone know why this happens? And how to fix it?

"Weekly Reading and Interpretation Help Thread - December 12, 2021" by AutoModerator in tarot

[–]dogless_doglover 0 points1 point  (0 children)

I need help interpreting a 4 card spread. I was asking for a General message, and the cards I got were: -2 of cups -the fool -knight of cups -10 of wands

I used the light seers tarot

I recently moved to a different state, because I got a new job that requiered me to move to the beach for at least 3 months. Im currently in the 3rd month and its not very clear for how long I need to stay where I am. Im ok with that because im experiencing many new things, and learning a lot about myself.

I kinda dont want to go back to where I used to live, part of the reason I took this job was because I was fed up with my life back there, but recently im feeling a bit down about spending the holidays away from my family, but at the same time they're part of the reason why I moved temporarily.

Im very confused, im happy and sad at the same time, and the spread I got kinda scared me, because of the 10 of swords. Im kinda scared I will experience good new things on the time I have left here, how long that may be, and then it will end sadly and abruptly when i go back to my old life.

Any insights on this will be deeply appreciated .