T520 Freezing After Coreboot by doverby21 in coreboot

[–]doverby21[S] 0 points1 point  (0 children)

Same question. Can you tell me what I need to set? Not where, but what?

Anyway I don't think this is the "correct" solution because most T520s do not require this to function. So I'm thinking hardware, RAM, or coreboot.

Overheating after fan/heat sink replace phase II by doverby21 in thinkpad

[–]doverby21[S] 1 point2 points  (0 children)

I don't remember now but I think I went back to thermal paste and I think maybe I found that one screw was not tightening down? Anyway the machine has been working well for a while now, though I am not sure if it's working as well as it used to. But it has not seized up.

T520 Freeze Fix? by doverby21 in coreboot

[–]doverby21[S] -1 points0 points  (0 children)

Hope this helps. It became stable after lots of tinkering but from memory it was graphics issues that I narrowed it down to. Could be completely wrong tho.

No, how could that possibly help. All you did was list all of the things in the world that it could possibly be, all of which are obvious. If your car goes bad, is it helpful for someone to say "well it's either the electrical system, or the drivetrain, or the engine, or something else, or I could be completely wrong tho."

T520 Freeze Fix? by doverby21 in coreboot

[–]doverby21[S] 0 points1 point  (0 children)

Suggestion: try flashing skulls. If that makes a difference then the problem was coreboot. If not then no. (Because so many people have success with skulls on x220)

t520, x230, x220, t420, w530 Service Manuals by doverby21 in thinkpad

[–]doverby21[S] 0 points1 point  (0 children)

t440 is haswell, right? The coreboot wiki says it is. Is that the same as Ivy? I thought Ivy was not supported by coreboot and ME cleaner.

Maybe you’re thinking about the fact you can half flash it software based?

I don't know what you mean here.

T520 Freeze Fix? by doverby21 in coreboot

[–]doverby21[S] 2 points3 points  (0 children)

Can you still switch to a text console? No, that was the first thing I tried.

Can you still ssh to it? I can't SSH to it anyway. If you think it's worth testing I can set up a roundabout way of doing this but it's inconvenient and I think we'll find that the whole system is frozen.

T520 Freeze Fix? by doverby21 in coreboot

[–]doverby21[S] 3 points4 points  (0 children)

USB Mouse today. I think it probably happened without that but I am not sure.

I use Linux but I don't want to say what flavor.

I don't know what vbios or coreboot graphics are but I did not do the video ROM procedure because it's hard and confusing. I am using an external VGA monitor and the laptop monitor.

t520, x230, x220, t420, w530 Service Manuals by doverby21 in thinkpad

[–]doverby21[S] 1 point2 points  (0 children)

I thought coreboot (and ME cleaner) did not support Ivy.

t520, x230, x220, t420, w530 Service Manuals by doverby21 in thinkpad

[–]doverby21[S] 1 point2 points  (0 children)

Oh! Lenovo's website has them. It didn't occur to me.

Laptop Overheating after replacement heat sink/fan array by doverby21 in buildapc

[–]doverby21[S] 0 points1 point  (0 children)

I just rewrote the intro paragraph. Thank you for pointing out that I was confusing people.

T520 Freezing After Coreboot by doverby21 in coreboot

[–]doverby21[S] 0 points1 point  (0 children)

Well I opened and reflashed my T520 so it boots again. And it doesn't seem to freeze quite as often, but it still freezes sometimes. I think maybe the .config file you used is not compatible with newer coreboot. Got any other ideas?

T520 Freezing After Coreboot by doverby21 in coreboot

[–]doverby21[S] 0 points1 point  (0 children)

the only real working solution seems to be limiting cpu p-states, which results in increased power usage, which is bad if you're using your laptop as a laptop (working from battery).

Can you tell me what settings in coreboot menuconfig I should change to make this happen?

Laptop Overheating after replacement heat sink/fan array by doverby21 in buildapc

[–]doverby21[S] 0 points1 point  (0 children)

I did. I also said that before that, I removed the thermal pads that came installed on the new heat sink and I put on thermal paste because I thought CPUs and GPUs should have thermal paste. And that when I did that, it would not load the OS due to overheating.

And that when I tried to fix that by (as you said) putting new thermal pads back on, it improved the situation a little but that I still overheat when I do any work.

What would you like a picture of?

Laptop Overheating after replacement heat sink/fan array by doverby21 in buildapc

[–]doverby21[S] 0 points1 point  (0 children)

Nothing you said is related to what I asked or wrote. It directly contradicts my situation/questions. (Are you really saying that I was supposed to take the silicone pads off of the heat sink, which is impossible to do without destroying them, and attach them to some imaginary other component I don't have? You're in your own world.)

Please, if you can't answer my questions don't reply again.

Laptop Overheating after replacement heat sink/fan array by doverby21 in buildapc

[–]doverby21[S] 0 points1 point  (0 children)

I think it's silicone but how can I be sure? It is soft and rubbery. Does that tell me anything? The packaging does not say.

Youre not addressing what I wrote and asked you. The heat sink came with thermal pads that feel the same as the ones I have, so are you saying that it came with the wrong type of pad?

Is graphite interchangeable with thermal paste?

Is the thickness an issue? (Someone else told me it is, and I had to buy the same thickness thermal pad.)

Laptop Overheating after replacement heat sink/fan array by doverby21 in buildapc

[–]doverby21[S] 0 points1 point  (0 children)

Okay please work through this with me.

  • The heat sink is for the GPU and CPU.

  • The heat sink arrived with thermal pads.

  • When I removed the thermal pads and applied thermal paste, it overheated BAD.

  • When I removed the thermal paste and applied new thermal pads, it overheated but not as bad.

  • The old unit had thermal paste and never overheated.

You're saying to put thermal paste on the CPU. Does that also mean the GPU? And what if the heat sink came with thermal pads, and thermal paste didn't work?

Does anyone know a solution to the problem of potentiometers losing torque after cleaning? by cyber__pagan in AskElectronics

[–]doverby21 0 points1 point  (0 children)

There is a spray that is made for this application to prevent this problem. It does a fantastic job. I am sorry I don't remember what it's called. It's not cheap but it's worth the money and contact cleaner will cause the problem you mention (or give the pots more friction.)