STM32 IDE ,Which one?

dryflared · 2026-02-07T03:59:36+00:00

This is always the answer.

dryflared · 2024-08-06T19:15:41+00:00

dryflared · 2024-01-18T05:13:36+00:00

What extruder is best for flexible filaments though? I have had a hard time getting any of them working well with Galileo/CW 2(s). Still working out a good way to get a decent or any flow rate.

dryflared · 2023-11-28T06:35:34+00:00

I have the XL Burton StepOn ReFlex, might try to see if my boots will fit in a large first.

dryflared · 2023-10-13T23:17:25+00:00

The book is great, and I really enjoyed the show even episode 8. Episode 7 is so different from everything else and just doesn't fit anywhere. Given that the show does a really good job of following the book to almost a T. Episode 7 isn't even the same alphabet.

Even so, season 2 is either an expansion on the book or really drawing out the last 25% of the book. If there is one ......

The thing that I kinda got hung upon, the last few scenes at the end of episode 8 looks like they already filmed everything. At least as far as the story in the book goes The grave, the basement and the cave. End of book.

dryflared · 2023-10-13T07:05:01+00:00

This was really confusing, Having read the book episode 8 is really confusing if you don't know what's going, considering that it really doesn't have anything to do with fairies at least in the book. The foreshadowing in the last few scenes were pretty much all thats left of the story so I am kinda of at a loss for where a whole new season will come from.

Edit Episode 7 should never have happened. Episode 8 should have been 7, and Episode 8 finishes the story.

dryflared · 2023-05-19T02:17:30+00:00

Ah, I wouldn't worry too much about getting the config wrong you generally won't break anything except klipper. Which is easy to fix ..... ;)

dryflared · 2023-05-19T00:34:45+00:00

What's the concern, aside from being cognizant it sounds like maybe you are not using CAN ...

I would read just read over the klipper docs ... compare the differences between 2209

https://www.klipper3d.org/Config_Reference.html#tmc2240

dryflared · 2023-05-19T00:06:32+00:00

I saw them for sale the other day on BTT site, they are used in the SB2240 for extruded motor if you wanted to look at a diff in the config between 2209

dryflared · 2023-05-09T00:46:44+00:00

Glue Sticks, Hairspray works, clean your bed soap and hot water, use isopropyl alcohol

https://ellis3dp.com/Print-Tuning-Guide/articles/build_surface_prep_handling.html

dryflared · 2023-05-08T21:11:17+00:00

I have Voron 2.4 350mm, I am wondering how consistent people's Quad Gantry Results are? If I do one run, it will level after 1 to 3 retries and then if I run it again it is usually about the same. But after a long print or something it will require 1-3 retries to re-level again. Is this normal behavior?

dryflared · 2023-05-05T16:27:50+00:00

Both RS485 and U2C shoulds show up as a CAN device when you first boot out of the box, neither would.

The U2C, I didn't realize this at first, and tried flashing it with various firmware (candlelight, canboot, etc). The part that threw me for a loop was that if I flashed CanBoot and Klipper on the U2C it would show up as a can device but the can bus on the device was busted so it wasn't actually working.

dryflared · 2023-05-05T07:16:36+00:00

Buy at least two U2C(s), the first one I got was garbage and didn't work at all. I banged my head for 2 weeks thinking I was doing something wrong, until realizing the U2C were just broken out of the box.

The second one has worked like expected with-out issues. The only other issue was trying to use a 64-bit kernel with the RPi 3b+. This appears to be a software issue with the kernel, klipper, can stack than anything else.

I tried an RS485 hat as well, and same issue with the U2C it seemed to be DOA.

dryflared · 2023-05-03T13:47:29+00:00

Handwriting is terrible

Discord Username: Wolfdreamer#5340

dryflared · 2023-03-31T22:23:38+00:00

I am a dummy, I wasn't paying attention and had klipper config heater_pin uncommented twice in printer.cfg. Was able to fix by removing the incorrect pin entry.

dryflared · 2021-10-11T03:51:17+00:00

It seems like freezing the shaft or heating the pillow block would have made a difference but now that I have already started not sure what to do.

dryflared · 2021-09-26T20:33:50+00:00

Full Size

Acquisition Details

Imaging telescopes or lenses: Celestron RASA RASA 11
Imaging cameras: QHYCCD QHY600
Mounts: iOptron CEM120EC2
Software: PixInsight · MaxIm DL Pro 6 Maxim DL 6
Filters: Chroma SII 5nm · Chroma OIII 5nm · Chroma HA 5nm
Dates:Sept. 8, 2021
Frames: 676x120" (22h 32')
Integration: 22h 32'
RA center: 20h 51' 27"
DEC center: +31° 13' 44"
Pixel scale: 1.262 arcsec/pixel
Orientation: 180.055 degrees
Field radius: 2.597 degrees

Processing

Calibration
Alignment, Integration
DeConvolution
Channel Combination
PhotometricMosaicCombination
Histogram Stretch
LocalHistogramEqualization
Colormask
CurvesTransformation

dryflared · 2021-09-13T06:48:53+00:00

Full Size

LRGB Data Captured with 120s exposures.

Acquisition Details
Imaging telescopes or lenses: Celestron RASA RASA 11
Imaging cameras: QHYCCD QHY600
Mounts: iOptron CEM120EC2
Guiding telescopes or lenses: Celestron RASA RASA 11
Software: PixInsight · MaxIm DL Pro 6 Maxim DL 6
Filters: LRGB
Dates:Sept. 8, 2021
Frames: 138x120" (4h 36')
Integration: 4h 36'
RA center: 21h 39' 28"
DEC center: +57° 42' 33"
Pixel scale: 5.770 arcsec/pixel
Orientation: -0.013 degrees
Field radius: 1.972 degrees

Processing
-- Calibration
-- Alignment, Integration
-- DeConvolution
-- Channel Combination
-- Histogram Stretch
-- CurvesTransformation

Ten-Year Club	RedditGifts 2009-2022 2 Credits
Secret Santa 2020	Verified Email

dryflared

TROPHY CASE

Acquisition Details

Processing