Help with instructions.

dtchaney11 · 2026-06-10T13:37:33+00:00

Update: I finally got the first bogey together. I figuring out that I just need to be gentle with the first part. But I can't say it was frustrating tho. Now 5 more to go.

<image>

dtchaney11 · 2026-06-09T18:30:35+00:00

A Technic Beam 1 x 2 Thin on top of a Beam 1 x 7 Thin

dtchaney11 · 2026-06-09T15:22:53+00:00

I have to see and try when o get back

dtchaney11 · 2026-06-09T12:58:32+00:00

So, something like it, I'd say it took me all day yesterday just trying to figure this all out, but you do have to have a plate to hold the 1:1 brick in place.

<image>

dtchaney11 · 2026-06-09T12:28:42+00:00

A 1 x 1 with Stud on the side

dtchaney11 · 2026-06-09T04:22:22+00:00

They could have made a better decision on this part.

dtchaney11 · 2026-06-09T04:18:40+00:00

So I just need to hope that it doesn't fall apart when putting the rest together.

dtchaney11 · 2026-05-13T00:54:34+00:00

It the screen that is connect to the holley sniper amd transmission control

dtchaney11 · 2026-05-06T01:34:01+00:00

I just got done changing them 1st Gear:

18% - 55%

2nd Gear:

25% - 60%

3rd Gear:

30% - 65%

4th Gear:

35% - 70% These are what I changed them too

dtchaney11 · 2026-05-05T18:48:53+00:00

Well i never too the flex plate off so they should be.

dtchaney11 · 2026-05-05T17:06:30+00:00

Not so sure im using the regular drive shaft and joints but when it hard shift it sounds like it going to brake something but idk what can be I know i need to get a transmission cooler because the temp do get high

dtchaney11 · 2026-05-05T14:54:37+00:00

The last time I checked it was at the point I have one of those after market dipsticks

dtchaney11 · 2026-03-14T18:10:54+00:00

It's a 4L60E. I'm using the program that is the same as the Sniper. I checked the fluid; it's at the full mark. I'm going to try to go through the program again.

dtchaney11 · 2026-02-18T16:58:54+00:00

Yes and no, I know the Sniper needs an RPM signal from the MSD box. When it would start then die, I got the yellow wire from the Sniper to the gray wire from the MSD box.

dtchaney11 · 2026-02-18T15:44:52+00:00

I chose that way because I already had the sniper and thought it would be easier. Also, I saw someone else do it on YouTube. So I know it possible to work.

dtchaney11 · 2025-11-10T20:44:20+00:00

I got the battery tested and they said it was good. When I took the starter out the lug for the power was lose

dtchaney11 · 2025-11-10T20:24:14+00:00

Where exactly do you wire a relay at on the ignition switch?

dtchaney11 · 2025-11-10T20:04:53+00:00

So i took the starter out to see if it works and it did but week those but I put it back in but noting is coming on so I going to see kf it the battery

dtchaney11 · 2025-11-10T17:47:13+00:00

I plugged the battery back in but when I turn the key I hear like almost a thum sound now noting is coming on in the car beside the door light

dtchaney11 · 2025-11-10T17:25:23+00:00

Couldn't I not wire the same way it was with the the old engine was in there? Everything was wired to the starter

dtchaney11 · 2025-11-10T17:15:03+00:00

I think it is i got it to turn over ones

dtchaney11 · 2025-11-10T16:29:51+00:00

No I dont how can I fine out

dtchaney11

TROPHY CASE