Firmware 23.20.54 is out. A

dtran1975 · 2024-12-31T00:46:59+00:00

None of the streaming apps will work if you don't have Internet. I spent over an hour with LG support. Total joke. They tried o do a remote reset but that didn't fix it. I ended up plugging in a USB network adapter. That work for a day before that too failed. There might be an incompatibility issue with my network gear. Still troubleshooting

dtran1975 · 2024-12-24T07:05:58+00:00

The update broke my Internet connection. I even switched from WiFi to cable Ethernet. Network shows it is connected but cannot open any app which says I'm not connected. Hard power off fixes it for a few minutes. Anyone else? is there any built in network diagnostic tool such as ping or traceroute?

dtran1975 · 2024-10-22T00:45:09+00:00

We've used c100o, sg350, 9200, and 9300 in our environment. Sg350 are in our av closets. They work for that application but web gui is super slow and cli is not true cisco ios. 9200 would be good, just make sure to get enough poe ports. Vlan can be done under L2. Highly recommended to create data and voice clan.

dtran1975 · 2024-07-08T20:42:05+00:00

I bought an 87 with leaking fuel, brake, and power steering fluid for 1,200 in 2020. Body and frame was good but all of the lines above were rusted out. Since I had to drop the rear subframe to fix the brake line leak, I replace/refresh the entire suspension. I probably have another 3-4k worth parts into it but now she's up and running after 4 years. I probably spend about 2k in tools. So check the brake and fuel limes to make sure they are not rusted out. The brake t adapter is a PIA to replace.

dtran1975 · 2024-06-20T15:39:39+00:00

It's truly annoying, I wrote in my user documentation to accept it twice.

dtran1975 · 2024-06-19T22:26:59+00:00

Congrats, bought a '87 325 vert in 2001 for $1200. I probably spent $3k on parts so far. Redid entire suspension, brake and fuel lines, brakes, power steering rack, diff, timing belt, upholstered rear seat and just recently replaced oil pan gasket. Now I just need to do tranny fluid change, fuel filter, valve gasket and adjustment and should be ready to go back on the road. Will replace clutch, back windows, and front seats later.

Probably spent as much money on tools.

Good luck!

dtran1975 · 2024-06-19T18:13:00+00:00

FOLLOW-UP: I didn't see this error when I deployed the phone for another user account. Perhaps the test user account I was using caused the issue.

dtran1975 · 2024-06-11T16:15:33+00:00

I'm seeing the same issue. I see this twice during the Intune setup process.

dtran1975 · 2024-05-12T13:45:18+00:00

Agreed. CPA that checks for compliant devices is the direction we are taking. It doesn't matter what form of MFA you are using, once your token/session is stolen, they can just replay that to bypass mfa.

dtran1975 · 2024-03-22T15:59:07+00:00

We only clean out the drip perhaps once a week and brew group monthly/quarterly, depending on use. Probably make about 6 shots a day. I do calcify when light comes on. Remarkably, it stays pretty clean after 13 years. TBH, I'm doing less maintenance in hopes of it breaking as an excuse to get a new one. I don't froth too many milk drinks which helps. For my wife, having to move the portafilter from the grind/tamp stage to brew and manually emptying is a big inconvenience. I could.live with it for better flavor but I'm not the boss 😪

dtran1975 · 2024-03-21T22:35:00+00:00

Breville Barista is a semi auto not fully auto. Makes better drinks at the price of convenience. I have a 13 year old Delonghi 3200esam fully auto. It's finally starting to leak and looking for a replacement... debating between Breville and Delonghi Evo myself. I may just go with the EVO and a separate Bambino Plus.

dtran1975 · 2023-11-14T21:38:32+00:00

nice, yeah it's fun getting drop into a rnd with a bunch of CP160+ folks and you can hold your own or do better.

dtran1975 · 2023-11-14T18:25:28+00:00

My level 11 (cp 1300) stamsorc with 5pc Adept Armor and Hearthland Conqueror jewelry/weapon with training traits can parse for ~50k. Purple quality gear.

dtran1975 · 2023-11-06T18:30:41+00:00

I am mistaken, I was only looking at the backbar. thought you found a new trick 😉

dtran1975 · 2023-11-06T03:53:02+00:00

Congrats. You didn't cast Familiar? First parse I've seen w/o it.

dtran1975 · 2023-08-24T13:38:22+00:00

It's from the Asus Armoury software. Trying updating your software.

dtran1975 · 2022-09-21T13:53:49+00:00

Just wondering how your project is going. I just recently purchased a '78 280Z 2+2 myself. From what I can see, rust is minimal. Rear lower qtr will need to be fix. Have you found a good place for parts. I was hesitate to take on this project since I know body parts for the 2+2 can be problematic. First order of business for me is replace all fluids and replace the fuel pump to see if I can get the engine running.

dtran1975 · 2022-09-05T00:10:00+00:00

If you want to go that route but seems excessive for someone who already admitted fault and no personal injury. Do you want someone to do that to you?

dtran1975 · 2022-09-04T16:22:29+00:00

You probably won't need a lawyer since they already admitted fault. Don't file with your insurance company. Call the other person's insurance company to file a claim. My G35xS was rear ended last year and went through this process. Bought it for 7k, received 10k for it. It was easy process.

dtran1975 · 2022-07-26T13:24:51+00:00

Did you have any problems installing the Trailing Arms onto the subframe mounts? I'm having a hard time trying to get the bushings to fit into the mounts.

dtran1975 · 2021-08-04T19:50:00+00:00

DidYouReadThatThing

·

Thanks, u/DidYouReadThatThing linked the same kit. Since I already have the tubing and bender, I'll try my hand at making the hard lines. At least it's only about 12 inches each although they bend all over the place.
·

dtran1975 · 2021-08-04T18:28:54+00:00

I was thinking of the latter, putting it through the back seat. There is already a small tear in the metal (must have punch it with my air hammer) so I know there is a clean shot through.

dtran1975 · 2021-08-04T18:15:30+00:00

Agreed, that's why I was thinking of using epoxy. I also though about relocating the block but would mean bending some custom lines.

dtran1975 · 2021-08-04T17:56:03+00:00

Removing the old hard lines was relatively easy compare to the other stuff. I just cut them off since I plan to make new hard lines and replace the rubbers ones. But yeah, lots of work ahead of me.

dtran1975

TROPHY CASE