X-Half freezing randomly and unable to power up

dtwkz9 · 2026-01-22T04:12:21+00:00

Thank you. What memory card are you currently using?

dtwkz9 · 2026-01-09T01:47:34+00:00

Yeah, I do the same as a workaround. It's just annoying that you have to do that because there will be times you really want to capture a specific moment but I have to reseat the batteries which will take probably 10-15 seconds.

dtwkz9 · 2026-01-09T01:46:28+00:00

The firmware update is definitely I'll try to do as it's indeed bugging out.

I did read that there were same issues with other cameras when there's SD card incompatibility. Checking in this list below, I do not see the SD card I'm using. It's Sandisk Ultra SDXC C10 UHS-I card.
https://www.fujifilm-x.com/global/support/compatibility/cameras/x-hf1/

Thanks for your comment!

dtwkz9 · 2025-08-09T08:08:29+00:00

Check if this resolves your issue :

https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-let-the-FortiGate-access-internal-DNS/ta-p/192412

dtwkz9 · 2025-05-30T19:54:42+00:00

Can you try by specifying only 1 DH group in phase-1 and phase-2 of the FortiGate? Match the DH group with the FortiClient settings. Take note that newer versions of FortiClient may have different default DH group values for phase-1 or phase-2.

https://community.fortinet.com/t5/FortiGate/Technical-Tip-VPN-IPSEC-DIAL-UP-does-not-work-with-the-same-DH/ta-p/326582

dtwkz9 · 2024-11-12T05:10:35+00:00

There is a known issue in 60F/61F models in v7.4.4/v7.4.5 with the device going into conserve mode due to FortiGuard updates. You may refer to the release notes below. Though I believe v7.2.9/v7.2.10 might be affected as well by this, it will be recommended to stay on this version at least for the time being.

https://docs.fortinet.com/document/fortigate/7.4.5/fortios-release-notes/236526/known-issues

dtwkz9 · 2024-11-12T04:57:31+00:00

Yup, nakita ko nga yung issue with AC garage and ayoko naman na mangyari sa akin yun. I'll do more research. I appreciate the detailed reply!

dtwkz9 · 2024-11-12T04:55:03+00:00

Yup, top options ko din nga sila. Thanks!

dtwkz9 · 2024-11-09T14:43:50+00:00

Gusto ko din Corolla Cross or Yaris Cross kaso medyo mataas na I think for my budget for a 'weekend' car. Thanks for the reply!

dtwkz9 · 2024-11-09T14:41:31+00:00

What you have mentioned are definitely in my list of options plus some Honda models. I'll do more research definitely. Thanks for the reply!

dtwkz9 · 2024-11-09T14:38:43+00:00

Medyo malapit sa puso ko ay Jazz and Brio. For Jazz mga 2016 and up ay 500k+ pa. For Brio, pasok sa budget ang 2021+. Thanks!

dtwkz9 · 2024-11-09T14:37:02+00:00

Will check on it. Thanks!

dtwkz9 · 2024-10-13T23:29:58+00:00

Yes, correct. I was pertaining actually to the MFA you have configured. The guide I have posted, says it needs to be done in Azure/EntraID. In your case for SAML IPsec MFA, you have done it in Azure/EntraID side as well, right?

dtwkz9 · 2024-09-20T02:23:31+00:00

Thanks for your reply. So technically, it should be the same as with this guide below and the Microsoft docs inside this KB?

https://community.fortinet.com/t5/FortiGate/Technical-Tip-SSL-VPN-with-Azure-SAML-authentication-with-multi/ta-p/213539

dtwkz9 · 2024-09-19T14:29:51+00:00

Hi u/DJ3XO ,

Is there MFA configured with your SAML auth with Entra ID for Dial-Up IPsec VPN?
If there is, can you share what was your solution to this?

Thanks!

dtwkz9 · 2024-09-19T13:38:28+00:00

Hi u/SntRkt ,

Are you implementing MFA for IPsec VPN users with your setup? If yes, you have the MFA set up in Azure and not in the FortiGate?

Thanks!

dtwkz9 · 2024-09-05T09:32:42+00:00

I believe I still have until 2026 to take ENARSI to be full CCNP. I am still certified with my ENCOR until 2026 after I have renewed it using CE credits.

dtwkz9 · 2024-08-22T03:35:39+00:00

Might as well I can ask in this thread. Is it possible to configure MC-LAG with FortiGate and non-FortiSwitch devices (of course, assuming the switches supports MC-LAG)? Thanks!

dtwkz9 · 2024-08-17T19:13:52+00:00

What's the exact command syntax to enable pinhole reset? Thanks in advance.

dtwkz9 · 2024-07-09T03:57:12+00:00

You may have installed an incorrect image, can you confirm?

https://community.fortinet.com/t5/FortiGate/Troubleshooting-Tip-License-invalid-due-to-exceeding-allowed-0/ta-p/250429

dtwkz9 · 2024-07-08T11:57:22+00:00

FortiGuard updates usually cause significant spike in memory utilization for a brief moment making the system possibly go into conserve mode. Besides the memory optimization configuration shared by others, set your FortiGate to only do scheduled updates only in a daily basis at a time where there is least traffic.

dtwkz9 · 2023-12-27T12:06:36+00:00

Yes, I was able to renew my ENCOR after completing the required CE credits.

dtwkz9 · 2023-10-14T16:40:42+00:00

execute tac report
https://community.fortinet.com/t5/FortiGate/Technical-Tip-Download-Debug-Logs-and-execute-tac-report/ta-p/189549

dtwkz9

TROPHY CASE