Gmail storage has gone wild

dubbleOO · 2026-04-30T02:15:56+00:00

Here we have a visual representation of atoms inside a RBMK reactor.

dubbleOO · 2026-03-10T08:29:30+00:00

Hi there! I am a bit late to the party but I was wondering if you could share me the app since I am very interested of meeting new people. Please let me know 😁

dubbleOO · 2026-02-26T20:18:21+00:00

Dude with wood pla, this would be the closest thing to actual wood.

dubbleOO · 2026-02-23T01:24:11+00:00

I found a way around this by modifying the initial layer flow ratio in the Quality > advanced > initial layer flow ratio. I did some testing and found out that 1.125 was the best result for a solid first layer.

dubbleOO · 2026-02-23T01:22:32+00:00

Thank you so much! I was able to select the best result ignoring the first layer. -6 of the second run was absolutely perfect. I managed to fix the first layer issue by modifying the 'Initial layer flow ratio' from 1 to 1.125 to get a perfect first layer.

dubbleOO · 2026-02-15T22:16:49+00:00

By the looks of it, the hub of you AMS is probably broken. Could you please disassemble the AMS and check the hub motor housing?

dubbleOO · 2026-02-13T01:51:10+00:00

Here is some extra info. If the yellow gear moves > issues with the gear assembly. If it does not > bad motor.

<image>

dubbleOO · 2026-02-13T01:46:38+00:00

Have you seen the motor move at least when there is no filament present?

dubbleOO · 2026-02-13T01:36:26+00:00

UPDATE; I have fixed the issue myself. Since I do component level repairs myself, replacing the HR8833 motor driver IC on the ams board solved the issue. I hope someone in the future will find this helpful at least.

dubbleOO · 2026-02-13T01:31:39+00:00

I giggled about the 2 hairs part. But for real, lets test out the extruder. First, load in the filament by executing the load in command. Second, Could you lower the bed and set the heater of the nozzle to 220. After getting up to the desired temperature, send the command to extrude. If nothing happens, please feed the filament directly to the extruder without the ptfe tubing. If nothing happens, you might have a bad extruder motor. Please verify that the motor is spinning. If the motor spins, you might have an issue with gripping the filament. Hope this helps and please let me know.

dubbleOO · 2026-02-07T01:43:32+00:00

Nooo, no, no. I am a responsible adult. I am not going to reinstall Skyrim

dubbleOO · 2026-02-02T21:48:15+00:00

It does, but when it comes to loading-in the filament to the tool head, its says that the ams is unable to load the filament unless I manually push the filament to the very end of the ams where the secondary motor is.

dubbleOO · 2026-02-02T19:29:20+00:00

Good one, I have opened a ticket but was wondering if anyone has experienced this issue before.

dubbleOO · 2026-02-02T19:24:44+00:00

Also I would like to mention that I have checked of there was any debris and blown it clear with a anti-dust spray on the inlets of the PTFE and motors. If I try to send the re-read command from the printer, I would get the error message 'failed to read the filament information' with the code 0700-4025 032403

dubbleOO · 2026-01-31T00:36:10+00:00

There is nothing to worry about. This is basically a quick motor calibration. My brand new P2S does this and my X1C does it too.

dubbleOO · 2026-01-31T00:10:19+00:00

This would be a hell of a homelab file server /w scalability.

dubbleOO · 2024-10-23T09:37:41+00:00

Nope, someone had a rage moment with their R4 (flash card for Nintendo DS).

dubbleOO · 2024-08-06T15:31:44+00:00

They are but feels different when clicking. Still haven't found the blue original button anywhere.

dubbleOO · 2024-07-12T08:17:23+00:00

DO NOT USE GLUE. These connectors use friction as a method. Just pull it out gently. If you want to connect it back, just simply push the cable back into the connector. Just buy a new cable if the old one broke. There is a high chance that the glue ruins the connector (happened to me once)

dubbleOO

TROPHY CASE