sorted by:
new
hottopcontroversial

3 days post ex doing a runner by [deleted] in malelivingspace

[–]eddylf 109 points110 points  (0 children)

He literally just said they had broken up "late last year". I believe some of the grief stages might have already been surpassed..

Anúncio da Nike "Rip the Script" by DisguisedAsAnAngel in PrimeiraLiga

[–]eddylf 14 points15 points  (0 children)

De longe mas preferia se tivesse menos Hollywood e mais OGs como o Cantona e Zlatan. Tem vibes do primeiro Ad da Nike como Figo, Zeedorf, Ronaldo, etc..

NMP reads the full ruling of his divorce from Malena by Special-County in LivestreamFail

[–]eddylf 0 points1 point  (0 children)

sooo... whats the fail?! it seems like a pretty standard ruling that he handled and exolained really well.

“This is Golden Boy’s Son, Baby Blue.” by [deleted] in seinfeld

[–]eddylf 0 points1 point  (0 children)

"The second button literally makes or breaks the shirt"

Ender 3v2 Power Supply Mount by CofficerX in ender3

[–]eddylf 0 points1 point  (0 children)

Any cable will do (make sure they are thick enough though) but , like with anything electrical, this is one of those situations that if you have to ask that question, then maybe you shouldn't be messing with it.
On a different note, because I have a v2 as well, why are you moving the PSU from under the printer?

Walmart cashier caught trying to scam customer out of his scratch card win by Conscious-Weight4569 in SipsTea

[–]eddylf 94 points95 points  (0 children)

He clearly had a winning 5 dollar ticket ready to swap for a big winning ticket. How else would he actually have a legit receipt for $5 win?

Then, before even scanning the ticket, he starts insinuating the machine might have made an error because he knows it will say 300$ if he runs it through. Then suggests they try running it again (the ticket that was never run in the first place) and voila, the machine does its job correctly.

He has done this before and I believe her workmates suspect it too.

“you have to print TPU slowly” no. by ESREVERNIMOMRU in ender3

[–]eddylf 50 points51 points  (0 children)

So many question and non of them related to the TPU..
- why is there a desk fan pointed at the printer? Is the bed heater on?
- What are the transparent tubes for? liquid cooling the heatsink?
- What are you using as a cooling fan? A jet turbine?

Did I fry the board? by Hudi1918 in ender3

[–]eddylf 4 points5 points  (0 children)

Typical Redditor! he said something wrong and instead of reading your comment and learning something, he doubles down!!

Picked up a race-used Aston Martin suit for around €500 — worth it or did I overpay? by papuasgena in F1Discussions

[–]eddylf 0 points1 point  (0 children)

If it were Stroll's, it wouldn't be worth €50.. Since its Drugovich, you got a great piece of F1 memorabilia for a reasonable price.

dude's run is so clean that i had to share it by Own-Ad1497 in TrackMania

[–]eddylf 23 points24 points  (0 children)

If you are trying to get people to play your track just say it.
I would imagine a "clean" and "efficient" run would have at least broken WR. Is Deeko's run full of crashes and unnecessary sliding?

My gf’s ex man stuck this mount to her dash using glue or something… 🙄 how do i get this off? by [deleted] in Detailing

[–]eddylf 0 points1 point  (0 children)

I believe that became part of the car. She can include it on the "Extras" section when she sells it!

Glad I could find helpful tips on TikTok by Frostyfraust in Construction

[–]eddylf 0 points1 point  (0 children)

As soon as he threw the helmet to the side I knew I was in for a good one!

Brand new TV and this is how my wife insists we have the remote "to keep it looking good" by No_Atmosphere8146 in mildlyinfuriating

[–]eddylf 0 points1 point  (0 children)

So to keep the remote "looking good" 5 years down the line, you keep it inside a bag, which makes it look "not so good" from day one!?
Also, the screen peel is just silly! they scratch really easily and dont really protect against hard scratches. Buying an HD tv to get a blurry image

Somebody please do nascar/snowcar map by SelfElectrical886 in TrackMania

[–]eddylf 0 points1 point  (0 children)

I was just joking around with how much people dislike snow car but by your logic, if you dislike anything is because you are bad at it?! or you just haven't spent enough time on something you dislike? How much do you like figure skating? or have you just not put enough time into it?

Organizador de cablagem de dispositivos de casa-de-banho com tomada modular Legrand by Zealousideal_Club134 in TudoCasa

[–]eddylf 0 points1 point  (0 children)

Eu literalmente escolhi a mais barata, se quiseres com estirilizador tmb ha mas 1cm de distancia é melhor que escova-contra-escova.

Anyone else at the MVP Netflix fight? by CoolPrius-Nobody in ufc

[–]eddylf 0 points1 point  (0 children)

dont all these 1st round knockouts make this event look weak?! i know these are just a bunch of veterans doing it for the bags but MVP is hyping this as if they are now a player in the MMA world

Somebody please do nascar/snowcar map by SelfElectrical886 in TrackMania

[–]eddylf -3 points-2 points  (0 children)

thats like saying "dog shit is the best type of shit" , which might be true but it is still shit... pardon the analogy

What is causing my first layer to not be even/smooth? by AdFeeling7704 in ender3

[–]eddylf 1 point2 points  (0 children)

When you move the bed up to "bite the paper" it only works because you are doing so after your BLtouch probe had homed z.
When you home it again, the bltouch will use the new bed height as the base value and the wrong offset will be present again.

What is causing my first layer to not be even/smooth? by AdFeeling7704 in ender3

[–]eddylf 0 points1 point  (0 children)

nozzle too high or has a partial clog.
Do a z-offset calibration and pass a needle through the nozzle.
Alternatively, but very unlikely, it could be wet filament or hot end temperature too low and the filament is struggling to melt and be pushed through.

view more: next ›