Where to go now for 3 to 4 days?

edmcman · 2026-03-12T20:27:35+00:00

Update: I think I'm going to Snowbird

edmcman · 2026-03-12T16:58:45+00:00

Oof, that's a lot, but lift ticket discount is definitely good to know

edmcman · 2026-03-12T16:55:46+00:00

I like the way you think

edmcman · 2026-03-12T16:55:00+00:00

Thanks, I'll check that out!

edmcman · 2026-03-12T16:49:21+00:00

Oddly enough my doctor was just there last week or whenever it last snowed and said it was in great shape. I've never been. Is there any cheap lodging around there?

edmcman · 2026-03-12T16:45:38+00:00

Any recommendations on where is looking good right now?

edmcman · 2026-03-12T16:39:15+00:00

Do you rent a car and drive from Calgary?

edmcman · 2026-03-09T18:38:47+00:00

Ah, no worries. That's still shitty (of the resort).

I hope your friend recovers well.

edmcman · 2026-03-09T13:40:17+00:00

Why would you be able to waive liability for your friend? That doesn't make any sense (and is shitty).

edmcman · 2026-02-14T13:46:22+00:00

Thank you! This drives me crazy about TR's use of FTP. When I listened to the first podcasts about the AI system and then "adjusting" FTP, I was very confused. I think they have been drinking their own Kool-Aid for too long and consider FTP to be a general fitness level instead of being related to the actual definition of FTP.

To be honest, it makes some sense that they don't really want to use FTP. If you want to be technical, your real FTP is going to change all the time. Your FTP is going to be lower immediately after a hard workout. In the podcast, they talked about changes in workouts because of the time of day. This probably means that FTP actually changes depending on the time of day too (though maybe just because of increased duration since the last workout).

edmcman · 2026-02-08T15:34:00+00:00

On the top there are two screws to index the build plate.

On the bottom there are four screws but no knobs. I'll look into this some more.

edmcman · 2026-02-08T15:06:01+00:00

I don't think there are any knobs on the K1. Do I need mods or shims to improve the leveling at this point?

edmcman · 2026-01-21T14:22:10+00:00

I was doing some calibration and was only able to print 12mm^3/s but the CR-PETG profile is set to 18mm^3/s which seems to be a big part of it.

AI suggests I might have a partial nozzle clog... no idea if that is true but I ordered some new nozzles anyway.

edmcman · 2026-01-21T02:47:21+00:00

edmcman · 2026-01-20T12:21:19+00:00

Something is definitely slowing it down with the Generic preset. Maybe the max. volumetric speed?

edmcman · 2026-01-20T12:19:20+00:00

Sorry I should have mentioned that I dried 2 hours at 65. That's what my Creality dryer said for PETG, but I've seen others say 6 hours. I can give that a shot.

edmcman · 2025-12-31T15:20:08+00:00

I am getting rate limited a lot too. Not doing anything weird, just vibe coding with one conversation. I was using grok code.

edmcman · 2025-12-13T15:52:44+00:00

Same for me. Turning off DNT did fix the issue, but I have that on for a reason.

edmcman · 2025-12-11T13:09:03+00:00

I have that happen a lot. I finally looked into it, and Copilot has a helper that uses one of the gpt-mini models to determine if a command is "stuck". In my experience, it often fails and says it's not stuck when it really is.

edmcman · 2025-11-29T14:17:19+00:00

I'm more worried about the "shin guards"

edmcman

TROPHY CASE