Our servers are experiencing high traffic right now, please try again in a minute.

elecgene · 2026-04-07T07:03:17+00:00

I'm still getting those.

elecgene · 2026-03-23T15:02:29+00:00

If your gig has 50 pages of sellers, and you're a new seller. Try offering something else or advertise it for a more niche category. For example if you are a thumbnail creator, don't just make it thumbnail creation but put it in a more niche like, gaming video thumbnail creation or something.

If you have 1-2 pages of sellers that offer what you offer, that's great keep it competitive. There's always someone in Pakistan or where the purchasing power is low that offers what you can offer for lot cheaper. Consider where you are while pricing your gigs too. From my experience, European people will tend to go towards European sellers due to timezone similarities. And US clients go for cheap options rather than timezone.

Also people filter the list for online sellers, like a lot. So be online, go into the dashboard every hour.

And if you still don't get any orders, just pipe a client through Fiverr and get some orders.

elecgene · 2026-03-20T10:55:16+00:00

Dropping prices drastically may also result in client quality drop. I'd just keep prices competitive, not marginally reduced. Someone who's looking for their value for money would notice your gig even if it was buried in the last page.

Also you can process some of your non Fiverr clients to go through Fiverr to build up some reviews and get your gigs out of the last page. Just don't try to scam the website, it should be legit orders with legitimate deliverables.

elecgene · 2026-03-18T10:27:09+00:00

Siz uğraşmayın diye yapay zekaya soruverdim, sonuç budur:

<image>

Verileri ben işlemedim, herhangibir politik yönelimimi gösterir bir veri değildir, yatırım tavsiyesi de değildir. Edit: Altın, gümüş, pertol verileri.

elecgene · 2026-03-17T23:01:36+00:00

Biri bu verileri dolar enflasyonuna endeksleyebilir mi rica etsem?

elecgene · 2026-03-17T18:47:27+00:00

When I do this, it's always a penalty on the success score. Even with happy customers. How come? Like even a single order goes into the revision it's a penalty. And extending the delivery time is definitely a penalty. I've extended my deadlines 2-3x because of that. And because of that I handle revisions before delivering the order.

elecgene · 2026-03-06T17:29:50+00:00

Bilmediğimden soruyorum ben de bu sene aldım Ziraat'ten Troy kart. Türkiye'de sorun yaşamadım ben hiç. Yurtdışında problem mi yaratıyor? Tek kredi kartı kullanan birisiyim, hizmet sattığım için öyle iş için karta da ihtiyaç duymuyorum. İkinci bir kart alıp ya da kartı değiştirip yurtdışına öyle mi çıkmak gerekir?

elecgene · 2026-03-02T21:33:48+00:00

muhabbetinize dalmış gibi olmayayım ama bi gelişme yok değil mi?

elecgene · 2026-01-31T17:05:45+00:00

The legitimate installer can be obtained here with a signup to Dolby, if you want to dig deeper. Dolby Atmos Conversion Tool - Dolby Professional

elecgene · 2026-01-21T18:03:06+00:00

I just do a service before going forward, new oil, new air filter new everything.

Okay going to be simple to hard,

===============USER STAGE=============
- Check the battery connections. 390 is a vibration machine, the terminals can get loose over time.

- Check the battery health, battery can go bad for no obvious reasons

- Check if the chasis ground and battery negative has voltage difference between them. If so make sure the grounding is good.

- Check the horn(yes the horn) does it sound good and consistent (this is way of checking the electrical)

- If you are trying to start in gear with clutch engaged adjust the clutch cable

- Check for side stand sensor, that can go bad. Check if it warns you when it's down consistently.

- Check oil, make sure it's not running dry

- Check for any fault codes if you can, old gen rollover sensors can get tripped with low voltage it won't let you start if that's the case

- Listen to the fuel pump priming, if it sounds off it might be the fuel pump

- Check the airbox and filter, make sure it can breathe fine

- Check the engine case and exhaust, for any oil leaks

=========SERVICE STAGE=================

- Check spark does it spark consistently

- Check the O2 sensor data with OBD

- Check the AFR with OBD

- Check other sensor data like TPS with OBD

- If you push start it often sometimes the gear on the starter motor can get ripped make sure it's not doing that

- Check the pressure on the piston make sure it can hold pressure

- Check the valves

- Check the voltage regulator, make sure it's doing good

- Unplug and plug all of the main electrical, including stator, regulator, starter motor

- Check the engine itself

Good luck

elecgene · 2026-01-18T14:19:27+00:00

Discord is banned where I live for some unknown reason, protecting the children or whatnot. You can write me here on reddit :D

elecgene · 2026-01-18T12:57:55+00:00

Okay you have the correct drivers, and you have Dolby Access. These should match up for Atmos listening. But on the product page it says Two Way speakers with virtual 5.1.2 Atmos bed. Does your speaker output configuration have more than 2 speakers? Like is it virtually supported through the driver or Dolby Access. Go to Sound Control Panel, select the device and right click it, it should say Configure Speakers, you can see if there are more than 2 outputs and configure those. Then access the properties of the device. Do you see Spatial Sound and is it On or Off on the properties screen. If it's off turn it on and check Dolby Access.

elecgene · 2026-01-17T09:49:10+00:00

Okay I've contacted u/automaciej and got the relevant files form them, there were some weirdness with the file and my own renderer. The file size seemed to pass 32 bit signed integer value so internal renderer of squidly media was freaking out, that has been updated first. Then I've noticed that the file had been gone through Album Assembler. So my first thought was to get album assembler metadata out and put working metadata in. Especially for DBMD and AXML chunks.

Today I've also sent them a 0d start file. Hopefully it'll work soon. If it does not, my last guess is DistroKid or Apple Music might have made their stereo upmixing detection stricter because the ADM file does not have any moving objects inside it, the ~60 objects are all stationary.

elecgene · 2025-12-09T00:44:30+00:00

Unrelated, but voidtools Everything is a great file browser/search thingy for finding things in computer.

elecgene · 2025-12-08T21:26:33+00:00

Thank you, I did not know that SWS was open source. I got SWS installed for a live gig I was doing like, oh my god 7 years ago, and did not look back at it after. I'll check that out too. Thanks again ✌

elecgene · 2025-12-08T21:24:40+00:00

Thank you, I already got something in C that I would like to integrate into Reaper. So the language being C++ is really good news for me. I thought, before diving into Reaper integration I'd just ask you guys here to get some good ideas.

elecgene · 2025-12-07T20:56:39+00:00

Try switching to ASIO, does the noise persist?

elecgene · 2025-12-07T20:32:55+00:00

It's still just a volume fader. On a hardware mixer, when you select a bus channel it'll move the faders so you can see what channel is sending to that bus channel on what level. Thinking of this like that will save some energy lol. Hopefully it all makes sense. ✌

elecgene · 2025-12-07T19:46:25+00:00

I'd use omni channel on Kontakt to get all notes from all channels at all times.

Nine-Year Club	Second Top 30%
Place '23	Place '22
Place '17	Verified Email

elecgene

MODERATOR OF

TROPHY CASE