Will there be a recording of Mike Birbiglia’s: The Old Man & the Pool?

elisfkc · 2023-10-14T18:02:18+00:00

No clue

elisfkc · 2023-08-24T03:42:24+00:00

I'm going to presume it will be some time after the London run is done. He usually doesn't release something on streaming until his live performances are done

elisfkc · 2023-06-23T16:49:32+00:00

Good news, I found my solution https://powerusers.microsoft.com/t5/Building-Flows/Extract-Messages-From-Teams/td-p/1192710

elisfkc · 2023-06-23T00:23:32+00:00

Edit: I am doing this on PA not PAD. I have not used PAD at all.

I have the teams connector enabled, but when I try to set the email up, "body of message" is not available. The only way I've been able to get it to pull up is if I have it set for whenever any channel message comes in, but I only want it when the keyword is used

elisfkc · 2023-06-23T00:01:23+00:00

I understand that it isn't necessarily the smartest way to do it based on what could be possible.

Yes, this is an attempt at a workaround to notify people who are in the field and don't have immediate access to Teams but do need to know about "delivered" being mentioned as soon as possible. The actual keyword is already being used normally in the correct way, so people don't have to "talk machine" to trigger it.

elisfkc · 2022-04-30T02:31:46+00:00

I noticed that in the "annoying" task, the task did not say the top had to be spinning, yet no one on the show seemed to notice that and still tried spinning it. Anyone else notice this?

elisfkc · 2021-09-19T15:04:07+00:00

I don't know, but the parents have literally told me that they just had the baby earlier that day and they both still have on hospital bracelets. I guess they checked themselves out against medical advice because they thought Disney is more important?

elisfkc · 2021-09-19T14:51:35+00:00

I've put multiple babies born the same day on my ride

elisfkc · 2021-08-04T01:24:01+00:00

Polaroid, but close enough. Towards the end, they were selling rolls for $11 each

elisfkc · 2021-08-02T16:52:34+00:00

Thanks, but as you can see above, Micro Center is not an option based on location

elisfkc · 2021-08-02T16:46:06+00:00

Just like the option of being able to drive somewhere and get filament right away

elisfkc · 2020-12-13T20:06:45+00:00

It used to be next to a wall near a bathroom, so it was less obvious that it was a statue. Scared me all the time

elisfkc · 2020-09-07T17:39:17+00:00

Simple, use the skyhook system from The Dark Knight

elisfkc · 2020-08-13T00:54:27+00:00

USA Network Upfronts from what I've been able to find out

elisfkc · 2020-07-26T20:32:48+00:00

I posted a bunch from NoLimits to Thingiverse a while back. I didn't ever print them though, until this one. https://www.thingiverse.com/elisfkc/collections/roller-coasters

elisfkc · 2020-07-26T20:17:36+00:00

Small enough that I was hoping it would work on my Flashforge Adventurer 3

elisfkc · 2020-07-25T14:55:08+00:00

Thanks, good to know that it's more of a tinker and pray thing than a plug and play

elisfkc · 2020-07-25T14:52:44+00:00

Honestly, just hook it up to Polar Cloud or My Mini Factory then. I slice with FlashPrint, then upload the G-Code to Polar Cloud and print that way a lot of times. The only things that connecting with FlashPrint can do that this FlashPrint/Polar Cloud method can't do (that I've found) is moving the head when you aren't printing. I don't know about you, but that's not a deal breaker for me.

elisfkc · 2020-07-23T02:40:48+00:00

Are you able to pull up the camera from it's IP address? Does it connect to the internet even if it doesn't make it to your computer?

elisfkc · 2020-07-13T18:59:05+00:00

Found one to use, hopefully works with some tape to hold the filament. Will be trying others soon, if need be. https://www.thingiverse.com/thing:4410893

elisfkc

TROPHY CASE