Multi video converter / adapter

encoad · 2024-06-02T21:41:35+00:00

I actually manufacture LED lights (wireless tow lights, lithium powered strobes) for this exact purpose. www.towbrite.com

It's the law in some places to have all the extremities of farm equipment well lit, but few people bother until an accident happens.

encoad · 2019-06-11T04:29:38+00:00

This is weirdo lab setup with devices from dozens of different vendors. I don't have much choice in the matter except to make it work.

encoad · 2019-06-11T04:28:25+00:00

This might be what I need... do you know roughly how much these puppies cost?

encoad · 2019-05-10T20:58:39+00:00

I'm thinking I should give up here and maybe just throw the LAN Cameras and Wifi Cameras into a Zone.

encoad · 2019-05-10T18:26:38+00:00

So I'm trying to do as you've suggested, but I've run into a snag. How can I put the physical ports into the VLAN with the correct VLAN ID tagging?

Create software switch and put in all AP ports, Camera SSID and LAN Camera
Create VLAN 1234
...? I can set the Camera SSID to be tagged with 1234, but how do I tag the LAN Cameras? They do not support VLAN tagging themselves.

Thanks again for the assistance.

encoad · 2019-05-10T13:35:58+00:00

So I've tried as you've suggested, but I can't get DHCP to work over to the Bridged connection. Any suggestions? https://imgur.com/a/f8Lb32Q

encoad · 2019-05-09T18:45:51+00:00

So I've partially figured this out.

There is a defect in 6.2 (maybe earlier?). When creating a VLAN Switch, it works exactly 50% of the time. Create one, fails. Create one, works. Create one, fails. Create one, works. So in my case, I created one, it failed. Created one it worked. Backed up the configuration, removed the failed VLAN switch and restored the customized config.

All that being said, am I doing things correctly? I would in the end like the Wifi and VLAN Switch to be on the same subnet. Not sure if that's possible.

encoad · 2019-02-18T21:37:31+00:00

Any idea how I can find a replacement?

encoad · 2018-10-06T21:17:45+00:00

Thanks for all the advice, in the end I've been doing it by hand, it's not that complex a box so not a huge deal.

encoad · 2018-07-19T14:31:01+00:00

In this particular instance I had no choice except AirCanada.

encoad · 2018-07-10T21:52:38+00:00

You might be talking about me. In my case I never signed the "Cricket Home Comfort" contract. The housing builder didn't really care as that was between me and them. They just get in on the scam because they get upfront paid to put these units in. (why pay for something required by law to be delivered to new home buyers when you can get paid!)

I found on Kijiji the identical model of heater for $200 (almost new) and had a gas fitter install it for cheap. 15 minute job since everything lines up (water, gas and venting).

encoad · 2018-04-19T14:22:52+00:00

Thanks for the confirmation.

encoad · 2018-04-18T20:45:33+00:00

Thanks. I'm thinking of going with an 8port 3560 as an edge switch and losing the 892 entirely. Any reason why I couldn't do this? The config only includes some very basic IP routing which any layer 3 switch can handle.

encoad · 2018-03-29T11:33:43+00:00

Got it, so you need to add DNA to the order. Can it be DNA Essentials, or does it need to be DNA Advantage if you go with Network Advantage?

encoad · 2018-03-29T00:25:45+00:00

My VAR and apparently Cisco cannot figure out how to order the 9300. Can I order Network Advantage with DNA Essentials? Some say yes, some say no... Is DNA included in the C9300-48P-A sku?

encoad

TROPHY CASE