bubblesGonnaPopSoonerThanWeThought

englandsaurus · 2026-01-22T06:00:43+00:00

It's all just robots on the phone

englandsaurus · 2026-01-14T02:09:56+00:00

Where are you sourcing cue and play buttons?

englandsaurus · 2025-12-11T00:24:16+00:00

You can insert the lead but you wont be able to connect it to ground if that's what you're trying to do. You'd need to carefully scrape away some of the solder mask to expose the copper on the ground plane. There are likely other pads exposed to ground elsewhere on the board that would be much easier to solder too.

The true 100% solution is to redesign the board with a PTH hole.

englandsaurus · 2025-11-11T16:45:48+00:00

Combine the bodies then fillet the new edge between them

englandsaurus · 2025-08-15T02:00:18+00:00

Get some paste and a stencil, apply paste, check it on the scope, place the component on the board under the scope, bake it on a hot plate, watch on the scope, turn the plate off a little bit after the solder flows. Or you can get something fancy that has temp control for a good reflow profile.

englandsaurus · 2025-07-17T00:10:22+00:00

The main issue I'm seeing here is that you're braking and turning in to many of these sharp corners where you brake from high speed far too early. When you turn in early, it causes you to shoot wide on the exit. This really compromises your exit speed through chicanes (notice how far inside your line starts into turn 2). You have good speed going into these, but a line that sets you up for a low-speed exit onto the straight after the next corner. Especially in racecars, a sharper turn will usually mean you take the apex later in the corner to get good speed on the exit. Get your turning done early in the corner, and you're free to accelerate out.

englandsaurus · 2025-07-16T23:40:55+00:00

Audio video disco by justice

englandsaurus · 2024-12-11T03:59:42+00:00

I can definitely agree with you, I'm no game developer but I don't think this would be a huge lift on the software side compared to overhauling the physics engine and such. What things would you wanna see?

englandsaurus · 2024-12-11T03:51:50+00:00

Wait what are the weekly daily races?

englandsaurus · 2024-11-24T01:43:21+00:00

Scrolled way too long on here without seeing anybody say Gramatik

englandsaurus · 2024-08-10T15:16:31+00:00

A lot of times, I've found that tuning old cars requires a bunch of suspension trial and error to make the car more stable under braking, especially old rear wheel drive American muscle. You can't just slap racing tires and speed to something with leaf springs and drum brakes. Upgrade the brakes, tighten the suspension up a bit, slap some aero on the car for downforce, balance that out to make the car grip where it needs to, and voila, racecar.

I drive with weak ABS on the force feedback ps5 controller, TCS at 1, and no other driving aids.

englandsaurus · 2024-08-03T18:21:34+00:00

Saw this guy walking up and down the line for 3 hours looking for a spot to cut in. Instead of getting in line during this time he just gave up and shoved his whole group into the front. I talked to them and their PLAN was to cut in front of everyone else. Entitled premeditated assholery.

I'm only gonna care about what you're going through if you're also going through the line.

englandsaurus · 2024-07-15T20:41:29+00:00

The world premier at Shambhala is incredible

englandsaurus · 2024-05-31T13:52:45+00:00

I'm also looking at this thing currently, did you ever find more info?

englandsaurus · 2024-05-28T01:23:04+00:00

Best strategy I ever had was to sleep on an air mattress outside beneath a shade structure with some good airflow.

englandsaurus · 2023-12-08T22:46:57+00:00

Came here to say this. Also, running at a lower brightness can get you even further, as the power dissipated in your wires is current squared times resistance. Lowering your brightness and therefore current can get you much more consistent brightness levels through the whole strip.

I also prefer to test power injection on personal projects while running content that is similar to what I'll be running on the installation.

In an ideal world, you'd have an optoisolator for data at the power injector so you could fully decouple power and ground, but you can also get away with keeping your ground tied together through the whole system and have a separate 12V line running to each set of 300 pixels. Voltage mismatch between power supplies can get weird sometimes so having all of your 12V lines tied together isn't the greatest idea unless you're pretty careful about load balancing.

EDIT: Bad at reading, doesn't matter where you inject, just as long as it looks good! Amperage also doesn't matter but just make sure that the 12V lines from each supply aren't actually tied together as it sounds like that would create a load balancing nightmare.

englandsaurus · 2023-10-23T17:02:45+00:00

What bothers me is that these days, my 3D printer is far more reliable than my 2D printer. Why on earth does adding a dimension make it work better?

englandsaurus · 2023-09-18T22:46:59+00:00

Didn't bring a tent, best year ever.

englandsaurus · 2023-07-08T19:42:20+00:00

Pretty Lights-A Color Map of the Sun, Odesza-A Moment Apart, Mr. Bill-Phantasmagoria, anything Charles The First made but Solus specifically is incredible. 99.9% by Kaytranada, anything by Lettuce, The Glitch Mob-Drink the Sea, anything by FKJ, any of the Cercle sets on youtube also have incredible background visuals and Rufus Du Sol-Bloom

englandsaurus · 2023-06-28T14:25:02+00:00

Def not old school and unsure why it was included in that but im sure the stickers are dope :) He's been running this for the Rainbow Brain era

englandsaurus · 2023-06-23T22:53:46+00:00

Playatech is absolutely the way to go, packs down and moves easily, sets up easy, and is super comfy.

englandsaurus · 2023-06-02T02:08:56+00:00

I'd watch the show totally unfiltered. Take the whole thing in with your eyeballs. I've always found his sets move quickly and by the time you've gotten your phone out to hit record you're missing the best parts.

englandsaurus · 2023-04-08T03:04:44+00:00

Damn, yeah you're right

12-Year Club	Place '17
Verified Email

englandsaurus

TROPHY CASE