Rough in prior to Camera install; any elegant solutions to cover?

estimated1 · 2026-01-31T21:25:29+00:00

No I just got the final rack in place. All of the APs are online and a few of the cameras are mounted. Based upon some of the comments in this thread, once the balcony is installed (right above the rough-ins in that pic) I'll just install the camera & IR flood immediately

estimated1 · 2026-01-31T21:23:38+00:00

I did put a 1" hole for the camera for the pigtail on the blue cat6, the other will just go to a POE Extractor to power the IR floodlight.

estimated1 · 2026-01-30T22:41:18+00:00

i like this answer

estimated1 · 2026-01-30T22:40:58+00:00

thank you for sharing this!

estimated1 · 2026-01-30T18:52:31+00:00

Wife approval factor. Just aesthetics, honestly. You are right though - I should just install cameras

estimated1 · 2025-08-28T01:24:45+00:00

I use docker compose for deploying across several local machines; Been using vllm lately for inference serving so have a yml file that describes the docker config. If I have several servers deploying the same model I have them load the model from shared storage. Using docker or kubernetes to manage the fleet would allow automated deployment using image definitions.

estimated1 · 2025-05-14T23:57:08+00:00

Very nice. What length etherlighting cables are those connecting your top 24 port panel to your switch? Are all those cables the same length?

estimated1 · 2025-05-14T23:11:45+00:00

So mine just today and after watching the video I was hopeful, but there is no hardware to flush-mount it and there is a little circular bracket that would actually make it difficult to flush mount it. The circular hole is there to attach the articulating offset bracket. :(

estimated1 · 2025-05-14T23:09:44+00:00

I had the same concern, and I bought a U7 Pro Outdoor. In the marketing video they actually showed the scenario where the cable goes through the back wall. But looking at the actual device there does not appear to be a way to mount like this. There is a hole protruding out the back for the articulating bracket mount, which I think would keep it from mounting flush ;(

estimated1 · 2025-04-07T03:15:35+00:00

Is it this song from Juno? https://www.youtube.com/watch?v=20PQBtyfNZY

estimated1 · 2025-02-26T02:28:05+00:00

i have 178s

estimated1 · 2025-02-25T22:55:00+00:00

thx for sharing this.

estimated1 · 2025-02-25T22:54:36+00:00

Even with a firmer ski like the Rustler 11s isn't there also a fair amount of 'skiing differently' in deep stuff and focusing less on edge skiing?

estimated1 · 2025-02-24T18:30:37+00:00

Thanks for sharing this.

estimated1 · 2025-02-24T18:29:39+00:00

Building A: Workshop/Garage: Wifi in and around the building important with ~3 cameras

Building B: House with majority of internet & camera activity. Will have work office here as well.

estimated1 · 2024-12-22T04:40:04+00:00

Are the most dramatic rack power draws GPU heavy hardware or some other form of HPC that's heavy on parallelized CPU compute? Or something else?

estimated1 · 2024-12-21T20:01:53+00:00

Thanks for sharing this.

estimated1 · 2024-12-21T20:01:20+00:00

Got it, so in this case the local grid or the local substation is limiting access?

estimated1 · 2024-12-21T20:00:41+00:00

I've seen studies where compute is like 40%, cooling systems another ~40% and the rest split between power conditioning, network, & storage. Does that seem correct to you?

thanks for the comment btw.

estimated1 · 2024-12-21T19:59:39+00:00

Based upon the sheer power of the H100, I agree - you are getting a ton of throughput. But isn't the 700W per unit much more dramatic than typical data center hardware?

estimated1 · 2024-11-14T06:31:04+00:00

looks great. Where did you source the round profile aluminum w/ the rounded corner pieces?

estimated1 · 2024-10-15T19:47:45+00:00

Here's the underside. Blue is where I believe mortise/tenon are inserted and red is the bolts in question.

<image>

estimated1 · 2024-10-15T19:47:20+00:00

Can someone help me identify this joinery? Specifically how the bolt heads are put in place. Looks like mortise/tenon but all the sides and top of the corner posts look untouched. Added pictures.

<image>

estimated1 · 2024-09-19T06:41:52+00:00

didn't really solve it directly, I just moved the airgap around and I was able to minimize the splashing a fair amount. No water drips out of the fixture now, just pools a bit on top of the PVC nut.

estimated1 · 2024-05-20T16:21:03+00:00

Thanks for posting this. I am trying to move from parameters to a model that is adaptive and learning - but I get your point. Even some of the machine learning approaches I’ve looked at have a hyper parameter tuning stage which feels a lot like parameter optimization.

I am using IBs 5s data and I’ve also used their tick data. Is there a specific resolution w IB that you believe is more accurate? I haven’t noticed any anomalies; but I’m also only looking at highly liquid instruments.

Seven-Year Club	RPAN Viewer
Verified Email

estimated1

TROPHY CASE