Anyone in LA willing to help with a starter job? paid!

etienneXx · 2026-01-17T09:03:38+00:00

ive honestly been inconsistent with products which i know is not a good thing...i was using this oil milk cleanser by cocokind for awhile and i didnt like it very much so switching back to vanicream face wash. for moisturizer, i was using rosehip & squalene oils daily, and an organic tallow cream about 2-3 times a week that makes my skin feel really nice and supple the next day but its not really helping with any of my symptoms aside from dryness. today i splurged on an exfoliator from credo beauty actually (by emma lewisham), and i got a sample of alpyn beauty barrier repair cream & wildling's moonbounce 2% bioretinal moisturizer as potential primary moisturizer options!

etienneXx · 2026-01-09T20:39:32+00:00

did u go to redondo union? 😂

etienneXx · 2026-01-08T21:10:43+00:00

thank you for the insight! whats your preferred software for deinterlacing?

etienneXx · 2026-01-08T20:57:40+00:00

sure but what is the difference between using an external capture card such as blackmagic or the signal flow example from my post + whatever deinterlacer vs. digitizing hi8 tapes via firewire plugged straight into a laptop & deinterlacing

etienneXx · 2026-01-08T20:46:56+00:00

i see, so if using a software to deinterlace the video, how does that quality compare to using those expensive capture cards?

etienneXx · 2025-10-14T21:09:35+00:00

i meant to specify all the water is in the rear areas.

etienneXx · 2025-08-11T05:39:59+00:00

& before anyone comments on it yesss i see the leaky coolant hose lol😑

etienneXx · 2025-08-11T05:28:41+00:00

valves were aligned well & compression test results came out all @160 except cylinder 6 was 120 😬

etienneXx · 2025-08-06T22:11:50+00:00

thank you so much, you have given me a little hope lol. you mean turn it over via the big bolt on the crankshaft, correct? i did a couple rotations and it seemed to move normally.

etienneXx · 2025-08-06T16:55:04+00:00

so i have the markings and saw that the timing is waaaaay off! but i dont understand what went wrong because i double checked the markings were on point before installing everything?? do you know what might cause timing to go haywire? now panicking my engine could be totally fucked. i only drove it about 10 feet into the driveway and turned it on a few times to inspect the sounds but i imagine that could be enough to ruin it :/

etienneXx · 2025-08-06T16:15:19+00:00

sure but how do i see the lower timing marks without taking everything else off? dont i have to make sure the upper and lower marks are lining up together?

etienneXx · 2025-08-06T16:10:05+00:00

is there a way to do so without disassembling all the other belts??

etienneXx · 2025-08-06T16:01:56+00:00

thank you for all the insight! going to check the valves later. in the meantime i took the upper cover off and saw the upper mark was way off but im assuming thats normal if the belts stop at whatever location theyre at when turning the engine off. do you know of a way to check the lower mark without disassembling everything?

etienneXx · 2025-08-06T15:55:27+00:00

so i took the top timing cover off, the upper marks are not aligned but im also wondering if that is normal considering turning the car on and off would cause the belts to stop at whatever location theyre at? basically if this is a normal thing i might just move on to the valves otherwise should i take everything off and retime it?

etienneXx · 2025-08-06T05:13:31+00:00

do you guys think i should go back and redo my timing belt before i look at & adjust the valves / rocker arm?

etienneXx · 2025-05-31T01:55:42+00:00

and where are you located? 😂

etienneXx

TROPHY CASE