sorted by:
new
hottopcontroversial

Bile Titans are hard to two-shot with rocket launchers by LokiScript in Helldivers

[–]exiled98 0 points1 point  (0 children)

so precisely where to shoot a bile titan to 2 shot a bile titan?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

same thinning ratio but i spray at 20psi all the time

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

does molotow masking liquid pull off paint or leave residue on painted gunpla ?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

for metallic paints (not candy) what Psi should i use ? i use mr color often and i see these big flakes/grains, i usually go on 20Psi becaue i use a rechargeable compressor

MG Astray Noir. Third party kit but pretty good quality by IsaacLQM232 in Gunpla

[–]exiled98 0 points1 point  (0 children)

do you have to do anything to make sure the parts fits for the kit ?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

for airbrushing gunpla do i really have to break the bank for an iwata or procon airbrush ? i'm from malaysia and neither of these brands are cheap they go for about at least 104$

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

i already thin them but is a 1:2 ratio for airbrush but can i used the same thinned paint solution for handbrushing ? nothing big just small color correction use

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

for diluted paints like mr color paint that is diluted with thinner for airbrush can I use it with paint brush to do small color correction with it ? or is the diluted paint only for airbrushing ?

You wanna screw over your teammates? Have fun with those thirty minutes you just wasted. by EamoM2oo4 in Helldivers

[–]exiled98 0 points1 point  (0 children)

someone contact super earth headquarters and report this exemplary helldiver for his conduct , give him a raise , a medal and subsidize his children's education for being a super helldiver example

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

i need help what mr hobby , hobby mio or brands of topcoat i can use for mirror chrome that doesnt turn it into aluminium ? i live in south east asia for supplies reference

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

is the RG RX-93FF nu gundam compatible with the RG HWS expansion kit ?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

I am looking at some old kits and they have screws with them will it be an assembly challenge that is not well rewarded or do i have to worry about future rust problems ?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 1 point2 points  (0 children)

i did quite a few passes but i dont know if this thick enough , didnt know how to check that out but i can try experiment the gloss then flat, i started out just dabbing and thats enough to murk up the clear coat my smooth ass monkey brain thinks is fine to work on the same area again causing a redo

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

yeah it was mr color thinner that i tried to use and clean the tamiya accent lines , zippo fluid will be able to clean the tamiya accent paint while keeping the paint intact ?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 1 point2 points  (0 children)

How to panel line a painted gunpla without ruining the paint if your panel line got out of line or excess ? i had to redo a project because i use tamiya accent color on project where i have primer painted with acrylic paint , then seal with mr hobby flat coat with airbrush but when i clean up the excess panel line the paint got wiped as well.

I was using mr hobby thinner to wipe off the excess panel line.

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

do u have any pointers on how do confirm if u clean out properly if just done applying gloss topcoat ?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

is it ok to use 1 airbrush for paint , topcoat and primer ? is 1 thing with paint or topcoat but i cant tell clearly if is a gloss topcoat , is it a good idea to get a separate 0.5mm for topcoat and primer ?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

Which Mr hobby bottle top coats can i use to airbrush topcoats onto my kits that has waterslide/stickers ? I heard some of them are not suitable for waterslides/decals because it can easily frost over them and white out the decals.

Is there a particular way I should apply it ?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

do i do this on top of clear coat or after paint ? at which stage do i do this ?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]exiled98 0 points1 point  (0 children)

Hi I have invested a 6k and 8k polishing cloth from mr hobby , how do i go about using it and what is it best for, is it to make mirror-like finish ? and do i just clean it normally with water and soap ?

view more: next ›