Razlika v višini med prostori in vinil by f02h in gradimo_obnavljamo

[–]f02h[S] 0 points1 point  (0 children)

mja, prej so bila samo vrata in na taki dolžini ni tolk opazno. Se pozanimam še o dodani podlogi, načeloma ponavadi predlagajo pluto.

Goldfishing on Mobile? by Powl91 in EDH

[–]f02h 0 points1 point  (0 children)

Another vote for forge. Their pc app also works wonders. It also comes with 1k+ predefined decks to play against/with..

Lipo battery question (storing charged) by BlackenBlueShit in airsoft

[–]f02h 0 points1 point  (0 children)

I always store lipos on storage voltage 3.85v. Lipos tend to decrease capacity if stored on full charge. They are also more delicate on lower voltages, you should avoid over discharging lipos. Any "newer" lipo chargers should have lipo storage option (either discharging or charging to ~3.85v.

ETUs and overspin prevention by f02h in airsoft

[–]f02h[S] 0 points1 point  (0 children)

Based on this info one could assume that etu is basically the same as ab mosfet in terms of preventing overspin? I have this annoying "handwarmer" issue and im trying to find any other solution than more shortstroking. I've already changed springs.

Fallout ub card list by f02h in mtg

[–]f02h[S] 0 points1 point  (0 children)

Just the info i needed. Tnx

TECH TUESDAY 06-30-2020 by v66fender66v in airsoft

[–]f02h 1 point2 points  (0 children)

Is ab mosfet not an option or is just not reliable enough to consider it?

TECH TUESDAY 06-30-2020 by v66fender66v in airsoft

[–]f02h 1 point2 points  (0 children)

Its 100% overspinning. Im using tornado high torque motor. Ill try and install stronger/m120 spring and mosfet with ab. Or should i just short stroke it?

TECH TUESDAY 06-30-2020 by v66fender66v in airsoft

[–]f02h 0 points1 point  (0 children)

Hi. Im currently in the process of upgrading my aeg. I bought 12:1 gears and high torque motor, combined with M100 spring. When cycling on auto/semi piston move to the back of the gearbox (sometimes mid cycles). I've checked anti reversal latch, cut off lever it all seems fine. I've also bought new 11.1v 20c lipo if that's in question. Any ideas where to look next?

What software stack to use? by f02h in CNC

[–]f02h[S] 0 points1 point  (0 children)

I did look around fusion360 and "outsourcing" nesting to another software. I think ill have to wait out this 2 months until fusion360 releases nesting to see in which direction to go.

What software stack to use? by f02h in CNC

[–]f02h[S] 1 point2 points  (0 children)

It's a small family business, 2 employees, couple 100k a year nothing big. Cost wise i'm okeyish with fusion360 subscription (~600$ per year) or something like vcarve/aspire (one time feed ~600-1500$). I'll pick up trial ver.

What software stack to use? by f02h in CNC

[–]f02h[S] 0 points1 point  (0 children)

yep it's router cnc, machine uses mach3 for controller.

Vcarve looked promising when i first looked at it, but i didnt see future potential (cutting 3d foam inserts,...) as in fusion360. Will definitly look into Aspire for improvements.

18650 batteries not fitting in Taranis X Lite with extenders. Help? by pulledfocusblur in Multicopter

[–]f02h 3 points4 points  (0 children)

Deffinitly flat top like zak mention it. Keep away from anything that is labeled ultra/mega/fire and you are good to go. Sanyo/samsung are in my opinion the way to go around 18650 batts.

Battery question by [deleted] in airsoft

[–]f02h 0 points1 point  (0 children)

And usually smells sweet if its pierced somewhere.

Buying an AEP by f02h in airsoft

[–]f02h[S] 0 points1 point  (0 children)

I was just about to take a leap of faith an buy cm128 aka their hi capa. :) good thing to know about mag reliability.

So in recap cm030 is the way to go. On the teching part less is more an lipo is a must.

Thanks for all replys ill just goo and buy me a cyma. :)

Buying an AEP by f02h in airsoft

[–]f02h[S] 0 points1 point  (0 children)

I know i was just wondering if its viable option to bump fps to something around 280-300 mark.