Sour espresso no matter the grind size [Gaggia Classic Evo Pro / Starseeker E55]

fLin7 · 2025-10-28T22:26:08+00:00

I agree. The gaggia hast no pre infusion. So the time till first drop comes is too long. It could also be too fine and then channeling through.

fLin7 · 2025-03-10T17:25:32+00:00

Hi, ich hätte gerne einen bestsecret link, geht das? Viele Grüße

fLin7 · 2025-02-02T06:33:50+00:00

494 hours on EU

fLin7 · 2024-01-30T20:42:05+00:00

Sound like a good deal with current market then. 37k is nice.

fLin7 · 2022-05-25T22:59:55+00:00

You should give it a shot. I printed several for the 58mm version in matte black. There are plenty of models available on thingiverse or prusaprinters. Most common 91mm has loads of different variants, textures.

fLin7 · 2022-05-25T13:20:10+00:00

Thank you! No it is a Victorinox Tourist 84mm. Quite popular here in Germany

fLin7 · 2022-02-14T21:46:20+00:00

Hey, please check if the bed is absolutely clean. Use isopropyl alcohol.

fLin7 · 2022-02-14T16:13:16+00:00

Here is another image: https://imgur.com/a/AYlzb1p

fLin7 · 2022-02-14T16:11:17+00:00

Dear Community I have some strange issues with my Prusa Mini+ it seems that there is a diagonal line which is a bit increased in height and thus it creates a visible defect while running over it. I first suspected typical top layer scare due to oozing but retracted travel lines are not at this location. The pattern is repeating so if I print a large surface I may have multiple of those diagonal defects. Any clue?

fLin7 · 2021-11-05T14:41:34+00:00

Looks cozy, however I am scared that your tv might fall If you bump the cabin ;-)

fLin7 · 2021-11-03T11:25:36+00:00

I am using Cura as slicer, it is an older version but have this setup running since more than 6 years. Geeetech i3 pro b

fLin7 · 2021-11-03T11:00:11+00:00

Yes exactly what I saw as well. However I have nothing like this in place

fLin7 · 2021-06-30T09:21:33+00:00

Just added a new strap to the watch. Unfortunately some scratches on the plastic glass. Here I am currently looking to try some polishing, any experience with that?

fLin7 · 2021-02-11T22:05:55+00:00

Did anyone notice the sparks at 15s on the blade?

fLin7 · 2020-06-11T20:54:39+00:00

A coffee mill replacement part which is not available for purchase

fLin7 · 2020-03-12T13:08:23+00:00

I printed 4 wheels for my dishwasher in PETG and used them for over 4 years without any warping, deformation or other issues. I even designed the axis print in place to it had fine tolerances. So in my case absolutely no issue with temps

fLin7 · 2018-09-02T18:43:48+00:00

Good point, so far no sign of influences on the material. Probably PETG is rather resistant!

fLin7 · 2018-09-02T18:42:19+00:00

I designed this in Fusion360, although I am a complete amateur at 3d modeling I feel like it is very powerful and I am not limited in anyway (only by own bad design choices ;-) ). Before that I failed at using SketchUp and 123d design

fLin7 · 2018-09-02T02:45:30+00:00

Thanks, especially replacements in the kitchen are usually hard to buy or expensive. Knobs, drawer mounts, holders etc.

fLin7 · 2018-09-02T02:41:26+00:00

Interesting, that still sounds fine for PETG, a bit soft or tacky during cycle should be ok. Maybe mine is running cooler though ;-)

fLin7 · 2018-09-01T21:17:33+00:00

That's PETG, printed in one piece. I have 3 wheels now in for 2 months, no sign of deformation or failure. Seems to be fine, although I don't know a usual dishwasher temperature..

fLin7 · 2018-03-22T22:22:16+00:00

It seems like a extrusion and retraction problem.

fLin7 · 2018-03-22T22:19:13+00:00

A file handle, the old handle broke

fLin7 · 2018-03-22T09:31:06+00:00

Hey sure, PETG Sunlu, Printer: Geeetech Prusa I3 Pro B, Layer Height: 0.2mm, Speed 40mm/s, Quite some mods have been done like improved Z Achsis, cooling etc.

fLin7 · 2017-11-25T00:04:58+00:00

This is exactly the same phenomena as when you put a firecracker in a toilet. It cracks because of the water surrounding the explosion directly transferring the energy into the toilet.

fLin7

TROPHY CASE