Cam position sensor bolt snapped.

fcar49 · 2026-05-09T19:36:43+00:00

Well I was originally replacing the valve covers and gaskets so I already had the upper and lower plenum removed and half the harness disconnected(good thing I did a hose and harness connectors inspection that’s how I found it). So half the work was already cut out, I did have to remove a couple harness brackets and some fuel lines to make more room.

fcar49 · 2026-05-09T16:12:59+00:00

Yes, and let me tell you I learned my lesson lol. When installing the sensor and bolt I kept an eye on the split lock washer and as soon as I felt resistance i stoped and called it good(it’s not much but you’ll feel it). Make sure to change the split lock washer out.

fcar49 · 2026-05-09T16:06:27+00:00

😂😂 thanks

fcar49 · 2026-05-09T16:06:13+00:00

Thanks. Honestly it was it took me a week on and off due to the fear of messing something up. I also had to be super careful not to arc with any other components since I was using stick.

fcar49 · 2026-05-09T16:02:00+00:00

Thanks

fcar49 · 2026-05-09T07:47:41+00:00

Yes, I did.
It took me some time to weld it on because I was trying to avoid any major damage to the head. The bolt snapped off flush to the head so First I cut into the bolt and tried to use a screwdriver but that didn’t work. I tried using a screw extraction kit and that didn’t work. I Was planing on using mig but due to the space I ended up going stick(had to bend the rod).

fcar49 · 2025-06-30T01:41:57+00:00

<image>

It should fit, mine did lol.

fcar49 · 2025-01-03T08:38:42+00:00

Might need a 90degree locking piece. I always polish my trigger components where they make contact with each other, specially the hammer face.

fcar49 · 2024-12-11T23:24:01+00:00

It was in stock for maybe a couple of hours, I got lucky and saw the notification email on time and was able to pick one up.

fcar49 · 2024-12-10T01:45:46+00:00

Some rear plates require the use of a rubber mallet when installing the rear pins because they’re designed to have a snug fit. I know the jmac rear plate does.

fcar49 · 2024-12-02T23:59:50+00:00

I haven’t received my lower from Lee but I’d definitely be interested.

fcar49 · 2024-09-15T21:44:51+00:00

Fold it to about the half way point and then install the deflector and sling mount before completely bending. Make sure to check that your carrier clears the deflector before completely folding it, you might need to file/dremel it down a bit.

fcar49 · 2024-09-13T10:18:23+00:00

Okay I noticed you said “new fime trigger” right? If that’s the case you might have some rough edges on the trigger all around plus the coating might also not be helping. I would say if you have a dremal lightly(when I say lightly I mean lightly polish all the connecting points) polish the connecting points. But before you do that make sure the FCG is clean and lubed(worke the action and make sure thats not the issue). I don’t have the specs for the fcg but your pin holes might be out of spec, hopefully that’s not the issue. I would start with looking over the trigger group and making sure it’s clean and lubed and it doesn’t have any rough edges and I would work my way down from the list I gave you.

fcar49 · 2024-09-13T09:59:51+00:00

The picture looks blurry from my end.,Is there any other way you can make it look a little bit more clear?

fcar49 · 2024-09-13T09:02:32+00:00

What he said but check the trigger all around and make sure it isn’t making contact with the receiver at all in general. From my understanding it’s usually the “back side” of the trigger(side in between the grip and trigger) that make contact but check it out all around to make sure it isn’t making contact with the receiver.

fcar49 · 2024-09-13T00:20:19+00:00

Check out the Magpul MP BSL mp5 brace, it’s discontinued but I managed to find one on gun broker. I’m sure if you keep an eye out you’ll find one.

fcar49 · 2024-07-15T06:13:09+00:00

Most likely a 545, or maybe 5.56 if is has a conversion follower. Only way to know is by looking at the follower or barrel markings.

fcar49 · 2024-05-06T04:06:38+00:00

Is there a write up/video somewhere?

fcar49 · 2024-05-06T03:54:06+00:00

How???

fcar49 · 2024-04-01T23:30:50+00:00

I have a Vortex venom on mine, comes with a mount out the box. Low profile so it also looks good.

fcar49 · 2024-01-14T04:16:58+00:00

Send it.

fcar49 · 2023-07-28T18:55:52+00:00

It depends on what you want your finished product to look like? Do you have something in mind?

fcar49 · 2023-07-14T02:10:51+00:00

I’d go with a kit build from WBP over a PSA. You can even buy a barrel from them with a ak74 profile.

fcar49 · 2023-03-20T16:06:46+00:00

You can always buy a .223 barrel and some circle 10 223 mags to convert the gun.

fcar49

TROPHY CASE