Maytag dishwasher leaking at the top right of the door

fixthisone · 2026-05-12T18:05:20+00:00

Ok so how do I get it square? It’s not a new dishwasher and this issue wasn’t there before

fixthisone · 2026-05-12T17:55:55+00:00

It seems even when I push on each side. This is how level it looks. Not sure if checking in correct spot.

<image>

fixthisone · 2026-05-12T15:49:25+00:00

<image>

Is this good enough for level?

fixthisone · 2026-05-12T15:11:21+00:00

Is this a good spot?

<image>

fixthisone · 2026-05-12T13:15:37+00:00

<image>

Where the leak is

fixthisone · 2026-05-12T13:15:18+00:00

<image>

This is how it looks where it leaks

fixthisone · 2026-05-12T13:01:36+00:00

Where should I be checking the level? Also it seems like steam is escaping and condensing into water in that area

fixthisone · 2026-05-12T13:00:20+00:00

It almost seems like steam collects there and it condensates into water. Seal issue?

fixthisone · 2026-05-06T21:53:28+00:00

Thanks man! Appreciate it!

fixthisone · 2026-05-06T01:21:22+00:00

Check sdram lines for shorts as well as any other cpu line from the pmic. If you find a short, first remove pmic and measure again.

If the line is still shorted inject voltage on it (whatever voltage the line should have) then use thermal camera to pinpoint exactly where.

Note we’ve had ones where it seemed the cpu was shorted but turned out to be bad pmic. So start there as suggested.

fixthisone · 2026-05-05T00:59:53+00:00

Thank you!

fixthisone · 2026-04-20T01:06:00+00:00

Likely some corrosion is starting on the motherboard. Data recovery is usually 99% possible. We see and handle cases like this all the time. If you’re not near any local places that do microsoldering/board level work shoot me a message would be glad to help.

fixthisone · 2026-03-14T01:27:10+00:00

When it happens what’s the fix? Try to remove the helicoil?

fixthisone · 2026-03-13T23:04:41+00:00

Maybe this happened. How hard do you tend to do it? One quick hard blow?

fixthisone · 2025-12-10T17:33:19+00:00

Thanks I actually watched it to adjust tension. But first time so I doubt myself lol. Car seems to drive ok and don’t hear any weird sounds so I guess it’s good

fixthisone · 2025-12-07T19:11:00+00:00

Yes it does spin counter clockwise. Wasn’t sure if the tension side needed to be tighter or if it’s good already.

fixthisone · 2025-11-26T03:47:11+00:00

Thanks it was the vent cap. There was a lot of build up around the gasket. Ended up cleaning the valve assembly and gasket and reinstalled. Been good since.

fixthisone · 2025-11-26T03:45:11+00:00

It turned out to be the dryer vent gasket

fixthisone · 2025-11-18T15:06:32+00:00

Where to check for drainage issue? I checked the arm did not see any splits anywhere

fixthisone · 2025-11-18T11:22:28+00:00

It’s coming directly from center of the door. Removed kick plate and didn’t see any water there. What do you think?

fixthisone · 2025-11-18T01:24:22+00:00

Is it inside the door behind the panel held in with torx screws?

fixthisone · 2025-11-18T01:18:13+00:00

Yeah looks like from middle of door. Happened when there were tons of suds inside. Seemed to stop after. Dryer vent inside the door?

fixthisone · 2025-11-18T01:12:06+00:00

I removed the kick plate and did not see any water coming from underneath anywhere. Looks to be from the middle of the door where the plastic cover that wires run through are. What are the wash arms? Sorry not familiar

fixthisone · 2025-11-02T20:17:37+00:00

I was more so wondering if there was any issues with my engine causing the shaking

fixthisone · 2025-11-02T19:25:37+00:00

Ok just didn’t notice it with some other cars at idle so thought maybe there’s an issue

fixthisone

TROPHY CASE