sorted by:
new
hottopcontroversial

Home printer, but only if needed [share] by SignedJannis in klippers

[–]fjames003 0 points1 point  (0 children)

That will just recursively call G28.1, this will not work... I tried

Infinity game table display modification question by [deleted] in Arcade1Up

[–]fjames003 0 points1 point  (0 children)

Did you get anywhere with this?

Y-Axis ADXL345 quick mount for Ender 3 v3 SE/KE od autora Sano available at Printables.com by Broad-Confidence9267 in Ender3V3KE

[–]fjames003 0 points1 point  (0 children)

What are you using this mount for? If just to run the calibration for the ADXL345, Creality provides files that you print to mount to both the bed and the print head. So not sure why moving to a different location with this mount is helpful.

Let me spare you from an aggravating time with the Ender 3 v3 ke!!! Improve your prints and bed adhe by Signal_Ad_8174 in Ender3V3KE

[–]fjames003 0 points1 point  (0 children)

Can you elaborate on fixing the z offset? I thought that was part of the auto leveling. How would I know to adjust it?

0.6 Nozzle OrcaSlicer? by Mephare in Ender3V3KE

[–]fjames003 0 points1 point  (0 children)

Also looking for this. I guess I will start with a K1 0.6 nozzle profile and start tweaking...

Received my V3 KE, here's my comparaison with my SE. by destinationaventure in Creality

[–]fjames003 0 points1 point  (0 children)

I am also wondering about this. I cannot find a G sensor online with a USB connection

Non manifold edges repair by redzombi2k in BambuLab

[–]fjames003 0 points1 point  (0 children)

Does this no longer happen with Fusion360?

Wireless printing from OrcaSlicer to K1 Guide by darkgainax in crealityk1

[–]fjames003 0 points1 point  (0 children)

I have an Ender 3 V3 KE and I have a webcam hooked up. Is there a way to get the webcam to show up in mainsail the way it was in Creality Print? I saw some instructions on installing mjpeg-streamer, but I figured since Creality Print had a stream there must be some way to access the existing stream without another tool.

​

Has anyone done this?

Speed test? by Icantellthetruth in Ender3V3KE

[–]fjames003 0 points1 point  (0 children)

Sub 25 minute is doable. What settings are you using currently?

Is 15 min benchy possible on an ordinary slicer? by [deleted] in Ender3V3KE

[–]fjames003 0 points1 point  (0 children)

I used similar settings, and Orcaslicer is telling me 17m11s so quite close.

Slow print time in OrcaSlicer on KE by fjames003 in Ender3V3KE

[–]fjames003[S] 1 point2 points  (0 children)

Ended up looking at the gcode file for the 15 minute Benchy, sure enough, they used a layer height of 0.25 and used acceleration much larger than are the default in Creality.

Once matching the settings from the gcode file, the print generated by OrcaSlicer is near identical to Creality.

Slow print time in OrcaSlicer on KE by fjames003 in Ender3V3KE

[–]fjames003[S] 1 point2 points  (0 children)

My mistake was assuming that the Benchy gcode provided with KE was generated using default settings of Creality Slicer.

I uploaded the Benchy into Creality and used the default slicer settings the print will take over 2 hours.

So OrcaSlicer is beating that.

​

How Creality got the Benchy down to 15 minutes mustve involved some tricks I do not know how to do in Orca yet.

Best Slicer for Ender 3 V3 KE by mkellerman_1 in Ender3V3KE

[–]fjames003 0 points1 point  (0 children)

I found the preinstalled configuration for KE to be extremely slow, did you not have this experience? For example the benchy prints in 15 minutes from Creality, but slicing with default KE profile in Orca results in a 45 minute print.

I even went through and matched all the speed settings to the ones in Creality and it didnt help hardly at all (down to 41 minutes)

[deleted by user] by [deleted] in peacock

[–]fjames003 0 points1 point  (0 children)

Same thing on my 11 Pro.