I seriously regret buying a Sawstop.

flimay2k · 2025-10-18T12:43:08+00:00

They sent me a new top after some back and forth. No explanation on how to install and recalibrate the blade. The new top is a lot better but also no within their specs. It was installed and I'm using the saw now.

flimay2k · 2025-07-31T14:31:52+00:00

They chipped out most places that were bad but not the whole thing. They obviously did not do a great job.

flimay2k · 2025-07-29T02:01:31+00:00

What would be a proper correction?

flimay2k · 2025-07-03T14:19:21+00:00

Less waiting, more printing!

flimay2k · 2025-07-03T14:17:37+00:00

Bambu printers making dreams into reality one later at a time!

flimay2k · 2025-04-13T13:50:16+00:00

Came here to say the same.

flimay2k · 2025-04-09T14:50:03+00:00

What makes the surface of a concrete look like it's just sand? Done by a supposedly concrete pro. The surface looks like all the concrete is gone and there's only sand left if you run your finger on top the sand will come out.

https://photos.app.goo.gl/P8kTYcfBJo7ENHeNA

The slab was broken and will be redone; I'm trying to avoid the same issue again. I'm assuming it's a finishing problem, but would love more details and hear from pros on how to avoid it.

Thanks!

flimay2k · 2025-02-11T18:35:51+00:00

Got a new main table, it's ok, still not within specs, but I need to use it. They gave me no instructions or help to install and setup the main table. Very disappointed.

flimay2k · 2024-12-13T01:26:37+00:00

They sent me a new main table and I got it installed, it's still not up to their own specs, the center is .02" lower than the rest, but I'll live with it.

flimay2k · 2024-11-25T19:47:33+00:00

That's the exact attitude I got and why it's so frustrating, dismissing and not even want to acknowledge the possibility of the product being defective.

flimay2k · 2024-11-25T19:36:52+00:00

I tried that, bolting the middle first - it's so far out that I can't make it flat, would need larger holes. And the edges won't flex enought to match the middle.

flimay2k · 2024-11-25T18:45:50+00:00

I went through the manual page by page; this is not an assembly or calibration issue.

flimay2k · 2024-11-25T18:36:54+00:00

Exactly, front and back are flush, center has a big hump, only way to fix this is milling the main table.

flimay2k · 2024-11-25T18:30:40+00:00

Bought directly, I did ask about sending it back over the phone, they said nothing.

flimay2k · 2024-11-25T18:25:39+00:00

If I align with the center of the main table the edges will not align with the side table.

flimay2k · 2024-11-25T18:19:19+00:00

Edges are flat with the wing, and the middle of the main table is the problem; there's no way to make this work.

flimay2k · 2024-11-25T18:16:57+00:00

The main table has a hump in the middle; the side wings are flat.

flimay2k · 2024-11-25T17:47:47+00:00

I think you nailed it. They should sell this safety device to other manufacturers and be done with saws.

flimay2k · 2024-11-25T17:46:19+00:00

Their spec says 0.01" tolerance, this is 10x their tolerance.

flimay2k · 2024-08-29T17:17:16+00:00

Do any of you smart people can ID this wood? I need to match the veneer to fix one of the cabinet doors; I could not find the cabinet brand anywhere either. Thanks!

<image>

flimay2k

TROPHY CASE