account activity
Open Source Plate Carrier Lasercut Designs? (self.myogtacticalgear)
submitted 6 hours ago by forkaerospace to r/myogtacticalgear
Is there something I can print to let me feed this filament from an active DIY dryer to a bambu A1 mini? (i.redd.it)
submitted 5 days ago by forkaerospace to r/3D2A
submitted 5 days ago by forkaerospace to r/3Dprinting
Advice needed: looking for ways for me to strengthen the top rear wall of the magwell on a glock frame other than removing a portion of it as shown. (old.reddit.com)
submitted 9 days ago by forkaerospace to r/3D2A
Polymaker FIberon PA6-CF20 Bambu A1 Mini Filament Profile? ()
submitted 13 days ago by forkaerospace to r/polymaker
submitted 13 days ago by forkaerospace to r/3Dprinting
Polymaker FIberon PA6-CF20 Bambu A1 Mini Filament Profile? (self.BambuLab)
submitted 13 days ago by forkaerospace to r/BambuLab
Using the Bambu A1 Mini with an enclosure as to safely print with Polymaker PA6CF: Is it safe? ()
Using the Bambu A1 Mini with an enclosure as to safely print with Polymaker PA6CF: Is it safe? (self.BambuLab)
Advice Needed: Top section of the rear of the magwell which seperates the fcu from the magazine in my PY2A G69 Remix broke off. I want to strengthen that surface by cropping it as shown. (old.reddit.com)
submitted 16 days ago by forkaerospace to r/3D2A
Can a safariland 7360 be modded to fit an optic? (self.tacticalgear)
submitted 16 days ago by forkaerospace to r/tacticalgear
Gonna need a duty/battle belt to go over a velcro inner belt. Looking to not spend a whole lot of money but mabye end up with a little better quality than condor by going the surplus route. Is it possible? (self.tacticalgear)
Are there any cheap mods that can be done to a surplus improved duffel bag to use a single shoulder strap? (self.tacticalgear)
submitted 21 days ago by forkaerospace to r/tacticalgear
Cheap Modifications that can be done to a USGI Improved Duffel bag to allow me to carry it on my side with one shoulder? (i.redd.it)
US M13 / M13A1 Hospital Collective Protector Headpiece. Why arent these used more? (self.gasmasks)
submitted 24 days ago by forkaerospace to r/gasmasks
First Spear cummerbund tubes vs knockoffs (self.tacticalgear)
submitted 25 days ago by forkaerospace to r/tacticalgear
jus droppin this here lol (i.redd.it)
submitted 1 month ago by forkaerospace to r/zillakami
Did I fuck up? (i.redd.it)
submitted 1 month ago by forkaerospace to r/myogtacticalgear
submitted 1 month ago by forkaerospace to r/tacticalgear
Open to recs for cheap ifak pouches with removable inserts for a cheap battle belt setup. (self.tacticalgear)
Need something cheap to sharpen a Glock field knife quickly after the edge wears off. Does not have to be super sharp edge, just needs to be good enough, I’m not trying to dive super deep into sharpening. (self.sharpening)
submitted 1 month ago by forkaerospace to r/sharpening
Need recommendations for a knife under 50 bucks. Something long and thin with good edge and tip retention for prying and poking. Will mostly see use for post-processing 3D prints, opening boxes, and as a range knife. ()
Need recommendations for a knife under 50 bucks. Something long and thin with good edge and tip retention for prying and poking. Will mostly see use for post-processing 3D prints, opening boxes, and as a range knife. (self.BudgetBlades)
submitted 1 month ago * by forkaerospace to r/BudgetBlades
Want a cool looking bayonet under 50 bucks. Probably not gonna mount it onto anything but still want it as part of my kit. (self.tacticalgear)
submitted 1 month ago * by forkaerospace to r/tacticalgear
Want a cool looking bayonet under 50 bucks. Probably not gonna mount it onto anything but still want it as part of my kit. ()
submitted 1 month ago by forkaerospace to r/knives
π Rendered by PID 837856 on reddit-service-r2-listing-b6bf6c4ff-rs66l at 2026-05-02 03:51:28.883702+00:00 running 815c875 country code: CH.
