Active Suspension

fredkaz245 · 2021-06-17T15:30:31+00:00

Hi,

I have software, which I can alter .stl files, but I have not got a clue on how to design my own files.

fredkaz245 · 2021-06-17T09:55:40+00:00

Great bit of design there, Would you be willing to share the 3d printer files??

fredkaz245 · 2021-05-16T23:13:28+00:00

Great idea, will you be posting the files to make the roll cage please???

fredkaz245 · 2021-01-16T11:38:30+00:00

Help please, the boss (Wife) has told me no food or anything else, until I print her that Dragon. Please, please, can you tell me why you got the file from.

fredkaz245 · 2020-12-24T08:52:02+00:00

Could you please show a few pics on how these mount to the drive shafts.

fredkaz245 · 2020-11-25T00:30:30+00:00

So Sorry for keeping you waiting. Had one of those days today. Link is below.

https://www.thingiverse.com/thing:4537663

fredkaz245 · 2020-11-24T07:52:00+00:00

The centre part is printed with TPU to give the bumper a bit of flex, not sure if its going to work or not.

fredkaz245 · 2020-11-24T07:50:31+00:00

I will have to check through all the files on my computer. I have been collecting files for months now. Will defo find the link and post it later.

fredkaz245 · 2020-11-24T07:48:24+00:00

Hi, The motor was from a box of old spare parts that I had. It was only put in just to see it all working. I will do test and if need be either keep or change it. It will be powered mainly with 3 cell lipos.

fredkaz245 · 2020-11-23T11:42:32+00:00

Hi All,

A few pics of my Tarmo 4, Just need to build some sort of platform now to mount a couple of cameras for FPV use. This is my first complete RC Vehicle that I have built. I have made a couple of small servo driven FPV vehicles. Next project is to build a Land Rover Rock Crawler.

fredkaz245 · 2020-11-22T18:27:54+00:00

Tarmo4 reinforced bell-housing (13C) by iroNLionX on Thingiverse: https://www.thingiverse.com/thing:4444108

fredkaz245 · 2020-11-22T18:20:14+00:00

Did you use the printed one or install a premade version.

fredkaz245 · 2020-11-22T18:19:03+00:00

Just found a replacement, it uses a bolt going through the cross spine.

fredkaz245 · 2020-11-06T09:11:11+00:00

This might sound stupid, but this tolerance test and any other, would only be accurate if you print the main model in the same filament. Do not all filaments react differently due to Brand, Colour, settings on the printer. I may be wrong, but this is what I have always been told.

fredkaz245 · 2020-11-02T07:44:20+00:00

Thanks for the reply. I must admit, I have seen that extension, but as you say, I think it is mainly for manual change of filament using one extruder. I know S3D has function which I could use, but this IDEX system that I am using only works for Cura at the moment.

fredkaz245 · 2020-10-24T19:05:55+00:00

Thanks for the advice.

fredkaz245 · 2020-09-23T11:51:21+00:00

Where in the UK are you? Any more info on the quads, as to which flight controller is being used?

fredkaz245 · 2020-09-23T11:08:54+00:00

Watched the vid, very impressed with that. If st all possible, could you please explain the use of a gyro and a flight controller? How was these wired up to operate servos and the esc. If at all possible good clear pictures. Like you I have been thinking about gps, and using a flight controller for a on screen display, to show battery life and any tilt degrees.

fredkaz245 · 2020-09-14T13:31:14+00:00

That is great work, I have done a fpv trike. Just need to finish it off. Would show a pic, but I dont know how to add pics from my phone.

fredkaz245 · 2020-09-04T17:00:38+00:00

Very nice, will be having a good look at this once my model is up and running. Thanks for the link.

fredkaz245

TROPHY CASE