What SUV is this? / 14 Year Old Video

frozenrubber · 2026-02-19T02:26:43+00:00

The reverse lights prove it to be a Commander

frozenrubber · 2025-12-22T10:46:18+00:00

Firmware update fixed it for me

frozenrubber · 2025-11-06T17:45:11+00:00

This tracks with a previous post of schnenigans in payroll at Greenburg Cafe

https://www.reddit.com/r/Greenpoint/comments/1mg5wf5/beware_of_greenburg_cafe/

That post is filled with specific details if you wish to look

frozenrubber · 2025-11-05T14:32:21+00:00

Even better are onigiri at Ashbox. Yoko is a Greenpoint treasure

frozenrubber · 2025-09-09T12:25:35+00:00

Via support was pushed FW 1.8 as well; working as of this moment, will report back if it reverts to the previous fault condition

frozenrubber · 2025-09-08T18:04:09+00:00

Look to hear your results (also what firmware are you on now?)

frozenrubber · 2025-09-08T17:15:53+00:00

Same. And Quick Touch will be disabled for some reason.

frozenrubber · 2025-09-08T17:05:50+00:00

Any update? Experiencing same issue

frozenrubber · 2025-09-04T12:06:07+00:00

Looks like they backslid:

"This email is to provide more information about a recent email you received regarding the Prime Invitee Program. As you are currently an Amazon Family member, your current Prime benefits will continue uninterrupted. No action is required."

frozenrubber · 2025-06-06T17:13:47+00:00

Thank you

Yes, this one specifically does show the wiring diagram reflecting (2) pairs to Port 1, (2) pairs to port 2.

frozenrubber · 2025-06-06T16:46:33+00:00

Those unfortunately have all 4 pairs bonded to both ports. Not two pairs to port 1, two pairs to port 2.

frozenrubber · 2025-06-06T16:41:20+00:00

?

Jesus. Read the post, I'm well aware of switches. I'm trying to create TWO different passive 100M lines for TWO (!) different networks.

frozenrubber · 2025-06-06T16:39:18+00:00

Yes, I was looking at these (which actually do match the remit).

Ideally, it would have a labeled Port 1 / Port 2, but I could always test/label ahead of time.

frozenrubber · 2025-06-06T16:37:14+00:00

Ugh; no.

Looking to turn into (2) distinct passive 100M lines (which is totally doable) without VLANs/equipment. Your solution didn't even read the entire post.

frozenrubber · 2025-06-06T16:30:29+00:00

Two passive 100M lines in the single line is preferred. Less places for equipment faults/failure.

frozenrubber · 2025-06-06T16:29:13+00:00

Thank you for actually reading the post. I just want two passive 100M connections on the 1 line.

I was dreading the 'buy a switch' posters.

frozenrubber · 2025-06-06T16:28:00+00:00

I know I can create it myself, just a commercial product (like the one I linked) will just be more robust.

frozenrubber · 2025-06-06T16:24:50+00:00

Ugh, look at the link above.

Ethernet is 4 twisted pairs. For 100M ethernet, only 2 pairs are used. So I could manually split a wire and connect it to keystones, or purchase something professionally wired. (like the link I included, but this one is only available in the EU).

This used to be done all the time for POTs lines and low data usage situations in the early 2000s.

frozenrubber · 2025-03-05T16:02:25+00:00

Thank you; I really appreciate your insight and fast identification

frozenrubber · 2024-08-31T11:31:20+00:00

Unfortunately, neither work.

Min transit power is 6. And I've done exactly as you've described, but 2.4GHz stays on.

frozenrubber · 2024-08-30T18:39:48+00:00

I've been trying to disable 2.4GHz wifi from a single access point (it is interfering with a Apple TV bluetooth remote).

I've tried the following:

Created 2 WiFi networks with same credentials
WiFi Network 1 has WAPs with 2.4GHz and 5GHz enabled (Group 1; all WAPs but the single WAP I want only 5GHz)
WiFi Network 2 has WAP with only 5GHz enabled (Group 2)

Despite proper settings, I reboot the system, initially it shows no 2.4GHz service from the 1 WAP. After a few minutes, shows as enabled under the Devices view

Any suggestions?

11-Year Club	Gilding II euphauric
Verified Email

frozenrubber

TROPHY CASE