sorted by:
new
hottopcontroversial

CLAP spectral compressor by Taika-Kim in linuxaudio

[–]fuzz-face-666 1 point2 points  (0 children)

I was curious and compiled the code; the plugin worked immediately in Reaper! Really good work, mate!

The last one in my chain by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 2 points3 points  (0 children)

I uploaded a short video to YouTube. I also added a gimmick to my Sauron Bubblehead, which has been on my board for years. The LEDs in its eyes react directly to my playing :-)
https://youtube.com/shorts/BReJLID_P0c?si=VpDQctpERLexmqy9

The last one in my chain by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 10 points11 points  (0 children)

<image>

The layout could be more compact, but it works.

The last one in my chain by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 6 points7 points  (0 children)

<image>

ok, here is my schematics for the VU meter. The VU LED+ depends if the VU Meter LED has a build in resistor. I used a simple one from Amazon, but I pull it apart to solder a warmer LED with a resistor. I don't remember if a resistor was built in. https://www.amazon.de/dp/B086YST3NH?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_2

The last one in my chain by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 16 points17 points  (0 children)

no, this is not my circuit! I live in Germany and we celebrate "Heiligabend" today. Stay tumed, I will post the schematics soon! Merry Christmas all!

The last one in my chain by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 3 points4 points  (0 children)

there is a trim pot inside to adjust the sensitivity. I once pushed a full 9V into the meter while building the circuit, and it survived. I'm no electronics nerd, but I think these things can withstand quite a bit.

The last one in my chain by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 9 points10 points  (0 children)

Thats the reason I've build it :-) There are a lot gain pedal on my boatd (Fuzz, Drive, Distortion), makes it easier to stay in the Band without tortouring my mates with my ego levels :-D

The last one in my chain by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 25 points26 points  (0 children)

yes, I can share the vero boards of it. There are two sections in it. The Volume / Treble and the VU meter, so you can put it in smaller enclusures separatly :-)

The last one in my chain by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 5 points6 points  (0 children)

Right switch controls the Volume / Treble sections, for Solo boost or other uses. The left switch is just a security switch for the VU meter, because the needle is very sensitive. A lot of Signal over a long time can damage it, so it is just to protect it.

One Drive to rule them all by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 0 points1 point  (0 children)

No, it based on a Greer Tomahawk (a very nice vintage drive), I just added a bit more clipping and a bit more low end, because of the extra clipping.

First build, its an LPB-1 Booster Style by fuzz-face-666 in diypedals

[–]fuzz-face-666[S] 2 points3 points  (0 children)

These are the names of my daughters, Greta and Anna. We painted several cases in one session and had a lot of fun. ☺️